Rasonic RS-U9YW, Руководство по эксплуатации

Страница: 22 / 28

18
●
●
●
19
使
用
方
法
1
1
2
2
1
1
2
1
2
2
2
1
3
4
5
●
●
●
18
前面面板
支點
機體
支持部 面板力臂
提醒
空氣濾網取下及面板拆卸方法
前面面板打開置水平位置 ( 請不要用力過猛，否則會
損壞前面面板)。
此時，可將空氣濾網取下。
前面面板成水平位置，面板力臂往內使前面面
板支點與機體支持部嵌合。
前面面板打開置水平位置(請不要用力過猛，否
則會損壞前面面板)。
前面面板向左靠
前面面板右側繼續抬高脫出
前面面板再向右靠
前面面板左側繼續抬高,前面面板即可脫出
將前面面板向下壓後蓋上。
(左、右、中間下方輕壓）
機體．遙控器的保養
●
請用軟布擦拭。
●
避免用下列物品
請勿使用
40 度以上的熱水、稀釋劑等揮發性溶劑及
去污粉等物。 （使用化學抹布時請遵照使用注意事項
來使用）
●
前面板請勿用水直接清洗。
空氣濾網
●
機體表示部“濾網清洗”燈閃爍或亮時。
●
空氣濾網用吸塵器將污垢吸淨，特別油污請用中性清
潔劑輕輕清洗（避免造成濾網破損）後，放在陰涼處
陰乾，避免日光直接照射。
●
空氣濾網清洗時，不可用化學藥劑或熱水清洗。
●
本體上的濾網清洗燈：當機體運轉時間累計 500 小
時，此時開關機後濾網清洗燈會閃爍約 2 0 秒後熄
滅，如未復歸重新計時，再累計到 800 小時後則開
機後濾網清洗燈會閃爍約 20 秒後恆亮。
●
空氣濾網清洗完後，請在遙控器上“清洗復歸”按鈕
輕按一下馬上放開，機體發生嗶一聲 ( 本體濾網清洗
燈熄滅)。
●
因環境關係，濾網污濁程度會有差異，可自行提早清
洗。
19
使
用
方
法
1
1
2
2
1
1
2
1
2
2
2
1
3
4
5
20
nanoe G
負離子產生器
●
nanoe G 產生器使用乾棉棒清洗前，請務必關閉電源。
C8041-3890 22
22
Maintenance and Checking
(Cleaning and maintenance of the filter)
Please stop operation and turn off
the NFB before cleaning the unit.
Please do not wash the unit with
water directly.
Method of Removing the Air Filter and Panel Maintenance of the Unit and Remote Controller
Cleaning of Air Filter and Nanoe-G
Procedure of removing the air filter
Open the front panel to horizontal position. (Please
do not pull too hard, or might break the front panel)
Remove the air filter.
Please wipe with soft cloth
Avoid using items as listed below.
Do not use hot water (above 40°C), volatile solvent
such as diluting agent and putty-powder. (Please
follow the caution items while using chemical
cloths.)
Do not wash the front panel with water directly.
When the unit display panel “Air filter cleaning” indicator flash or is on.
Vacuum dust from the air filter. For special stain, gently
wash it (prevent filter breakage) with neutral detergent
and let it dry in the shade. Please avoid direct sunlight.
Do not wash the air filter with chemical agent or hot water.
Procedure of removing the front panel
Open the front panel to horizontal position. (Please do
not pull too hard, or might break the front panel)
Lift the front panel to the left.
Raise the right side of the front panel and draw it out.
Lift the front panel to the right.
Raise the left side of the front panel. Afterwards, it can be removed.
Procedure of the front panel re-insertion
Make the front panel to horizontal position. Make the panel force arm
inside and slot the front panel fulcrum and unit supporting part together.
Push the front panel downwards and close it.
(Gently push left, right and bottom center)
When the air filter is broken (please replace it immediately.) or
need replacement, please contact our dealers or services sites.
Front Panel
Front Panel
Fulcrum
Panel Force Arm
Unit
Supporting Part
Front Panel Air Filter
Caution