Rasmussen F Скачать руководство пользователя страница 6

Страница: 6 / 16

B) Burner Pipe

Ember Burners

D) 3/8 Orifice Holder

C) Orifice Spud

A) Burner

Plug

FIGURE 4

E) Flared

End

F) Rating Plate

Heat Shield

STEP THREE: BURNER PAN ASSEMBLY

Natural Gas Models; F, FH, FX and FXH (All other Models refer to supplied instructions)

NOTE:

If fittings do not come pre-wrapped with Teflon threaded tape, pipe compound MUST be applied to all tapered pipe threads

(except in #3 of Step 3) to prevent gas leaks.

DO NOT

use Teflon tape or pipe compound on

any

flared fitting threads.

1. Thread

Burner Plug

(Figure 4A.) into the

Burner Pipe

(Figure 4B) at opposite end of gas supply

and wrench tighten.

2. Thread

Orifice Spud

(Figure 4C) into

3/8” Orifice Holder

(Figure 4D) (Do not use pipe compound or Teflon tape here)

NOTE:

The Orifice Spud is a gas consumption limiter. Higher flames (and greater gas consumption) may result if

orifice spud is not installed.

3. Thread Orifice Holder into Burner Pipe and wrench tighten with the flared end facing rear wall of firebox (Figure 4E).

4. Insert

Rating Plate/Heat Shield

(Figure 4F) onto the threads of and the Burner Pipe with labels facing away from

the burner.

STEP FOUR: GAS SUPPLY CONNECTION

(NOTE: ENSURE THAT GAS SUPPLY TO FIREPLACE IS OFF)

1. Thread

1/2” FIP x 3/8” Flared Elbow

(Figures 5and 6A) onto the

Gas Supply Pipe

(Figures 5 and 6B) and wrench

tighten. If space between Gas Supply Pipe and Firebox floor allows, the flared end of the 1/2” FIP x 3/8”Elbow

should

face down. (Figure 6A)

2. With Burner Pan inside firebox at previously marked position thread one end of the

Flex Connector

(Figures 5 and

6C) to the

1/2” FIP x 3/8” Flared Elbow

and wrench tighten. Do not use pipe compound or tape on

any

flared threads.

3. Carefully bend the

Flex Connector

into position, connect to the

Orifice holder

and wrench tighten. If Flex Connector

is bent into too small of a radius it may kink or break causing air flow noise and/or gas leaks.

4. Proceed to Page 11 “Pan Medium Installation”

FIGURE 5
Side View

●

Keep the Flex Connector as

close to bottom inside edge

of firebox floor as possible

B) Gas Supply

Pipe

A) 1/2’ FIP X 3/8

Flared Elbow

Rating Plate/Heat Shield

C) Flex Connector

STANDARD MATCH LIGHTED (NATURAL GAS MODELS ONLY)

Содержание F

















Результаты поиска

Содержание F

Отзывы:

Похожие инструкции для F

Бренды по названию

Популярные бренды

Rasmussen F, Руководство пользователя

Результаты поиска

Содержание F

Отзывы:

Похожие инструкции для F

Бренды по названию

Популярные бренды