Rasilient PixelStor 5000 Скачать руководство пользователя страница 149

Страница: 149 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

7-112

dakem -E -C 6000: Display all the KEM messages.

dakem -E -C 6000 -s warning: Display all the KEM message of severity

warning and above.

dakem -T warning Set alert level to warning.

7.7.19

dalun

Use dalun to manage the lun masking table. This pertains to Virtual Drive presentation.

dalun - manage the lun masking table.

Usage:

dalun [options] [fields...]

Options:

-h: help

-a: add a new lunmask entry

-d: delete a lunmask entry. You should log off at

the host initiator before performing a delete.

This ensures the host has sent all data to

the storage array.

-p: print out all the existing lunmask entries

Required fields:

-n [host]

-g [disk_group_name]

-k [virtual_disk_name]

-P [parent_virtual_disk_name]

Notes:

The -P parent_virtual_disk_name is only required if the

virtual disk presented is a snapshot virtual disk.

Command Examples:

dalun -a -n host1 -g dg1 -k vd1:

presents virtual disk vd1 in disk group dg1

to host1

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды