Rasilient PixelStor 5000 Скачать руководство пользователя страница 118

Страница: 118 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

5-81

Description

– The System Health Alert lets administrators know that the system needs attention.

The System Health Alert utilizes all the disk drive LEDs and uses them to flash a warning signal.

All the LEDs on the disk drives blink approximately once per second. These lights continue to

flash until redundancy is restored or the unhealthy condition is corrected. This visible alert is

especially useful in dense rack implementations or situations where it is not easy to see or

access the back of the system. Once alerted, you can log-on to the web-based PixelStor
Storage Manager to ascertain the cause of the problem and use the system’s Status Indicators
(LEDs) to pinpoint the failed component and take corrective action.

Policy

– The System Health Alert is triggered whenever system availability degrades. For

example, the Health Alert lights flash when component failure or removal causes system

availability to drop below its original startup condition. It is also triggered by an unhealthy

system state such as an exceeded temperature threshold.

To View the System Health Alerts, click on System Health Alerts in the navigation area of the

System tab.

Figure 5-7 System Health Alert Page

PixelStor 5000

does not require redundant components to operate. If the system

boots up without redundant power supplies, network links or controllers, the System

Health Alert is NOT triggered.

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды