background image

4

INST

ALLA

TION

Raritan PH SuperFlush Marine Toilet Front View, Side View and Footprint

Tools Required

•  5/16" nut driver

•  Wrench or screw driver 

•  Bit for drilling mounting surface 

•  Hose cutters

•  Tape measure

Additional Parts Required  

•  Four stainless steel mounting bolts or lag screws 

(minimum 1/4" [6mm]) and washers 

•  1 1/2" I.D. discharge hose 

•  3/4" I.D. reinforced intake hose 

•  Hose clamps (two for each connection below 

waterline) 

MOUNTING TOILET

Mounting surface must be flat and solid.

1.  Install seat on toilet.

2.  Place toilet where it will be located.

 

Make sure there is room to route hoses.

 

Make sure seat will open properly.

3.  Mark location of toilet base mounting holes on 

mounting surface.

4.  Drill holes for toilet mounting bolts/screws.
5.  Secure toilet to surface.

2.76

[70]

8.86

[225]

4.33

[110]

2.16

[55]

E

9

(229)

F

6 3/16

[156]

A

B

C

D

SEE NOTE 1

INCHES 

(MM)

11 1/2

(292)

10 3/8

(264)

BOWL TYPE

MARINE

B

A

13 1/8

(334)

13

(330)

24 3/4

(629)

18 1/4

(464)

17 3/4

(451)

D

C

20

(508)

17 1/4

(438)

F

E

7

(179)

6 1/2

(165)

HOUSEHOLD

NOTE:

1. THE SEAT WILL OPEN WITHIN THE DEPTH OF THE BOWL (D),

HOWEVER, IT MAY BE DESIRABLE TO INCREASE THIS ANGLE 

 BY ALLOWING MORE ROOM AT THE BACK OF THE BOWL FOR 

THE SEAT TO OPEN.

2. MARINE STYLE BOWL, D DIMENSION IS 17 3/8 [442MM]

WITH HANDLE EXTENDED.

27 7/8

(708)

2 7/16

[62]

(SEE NOTE 2)

3. DIMENSIONS ARE FOR REFERENCE AS VITREOUS CHINA 

 DIMENSIONS MAY VARY +/- 5%.

L563  0316kgs

[110]

Содержание PH Superflush









Отзывы: