Rapid Engineering BH-40, Инструкция по установке, эксплуатации и обслуживанию

Страница: 10 / 68

BH-S
ERIES
I
NSTALLATION
, O
PERATION AND
S
ERVICE
M
ANUAL
4 of 59
SECTION 2: INSTALLER RESPONSIBILITY
The installer is responsi b le for the follo w ing:
• To install the heater, as w ell as the gas and
electrical s u pplies, in accordance w ith applica b le
specifications and codes. Rapid Engineering LLC
recommends the installer contact a local B
u ilding
Inspector or Fire Marshal for g u idance.
• To u se the information gi v en in a layo u t dra w ing
and in the man u al together w ith the cited codes
and reg u lations to perform the installation.
• To install the heater in accordance w ith the
clearances to com bu sti b les.
• To f u rnish all needed materials not f u rnished as
standard eq u ipment.
• To plan location of s u pports.
• To pro v ide access on all sides for bu rner ser v icing
and remo v al.
• To pro v ide the o w ner w ith a copy of this
Installation, Operation and Ser v ice Man u al.
• To ne v er u se heater as a s u pport for a ladder or
other access eq u ipment and ne v er hang or
s u spend anything from heater.
• To ens u re there is adeq u ate air circ u lation aro u nd
the heater and to s u pply air for com bu stion,
v entilation and distri bu tion in accordance w ith
local codes.
• To safely and adeq u ately install heater u sing
materials w ith a minimal w orking load of 75 l b s
(33 kg).
• To ens u re the heater is placed in an appro v ed
application.
2.1 Wall Ta g
A laminated w all tag is a v aila b le for the heater as
a permanent reminder of the safety instr u ctions and
the importance of the req u ired clearances to
com bu sti b les. Please contact Rapid Engineering LLC
or yo u r RAPID
TM
independent distri bu tor to o b tain the
w all tag. Affix the tag b y peeling
off the b acking of the adhesi v e strips on the rear
s u rface and position the tag on a w all near the
heater (e.g. thermostat or RAPID
TM
Controller).
A copy of the w all tag (P/N 91037920) is ill u strated on
the b ack co v er. For an immediate sol u tion, yo u may
affix this copy on the w all near the heater.
Kno w yo u r model n u m b er and installed config u ration.
Model n u m b er and installed config u ration are fo u nd on
the bu rner and in the Installation, Operation and
Ser v ice Man u al. See Page 6, Figure 3 through Page
9, Figure 12 . Write the proper clearance dimensions in
permanent ink according to yo u r model n u m b er and
config u ration in the open spaces on the tag.
2.2 Corrosive Chemicals
Rapid Engineering LLC cannot b e responsi b le for
ens u ring that all appropriate safety meas u res are
u ndertaken prior to installation; this is entirely the
responsi b ility of the installer. It is essential that the
contractor, the s ub -contractor, or the o w ner identifies
the presence of com bu sti b le materials, corrosi v e
chemicals or halogenated hydrocar b ons* any w here
in the premises.
* Halogenated Hydrocarbons are a family of
chemical compounds characterized by the
presence of halogen elements (fluorine, chlorine,
bromine, etc.). These compounds are frequently
used in refrigerants, cleaning agents, solvents, etc.
If these compounds enter the air supply of the
burner, the life span of the heater components will
be greatly reduced. An outside air supply must be
provided to the burners whenever the presence of
these compounds is suspected. Warranty will be
invalid if the heater is exposed to halogenated
hydrocarbons.
2.3 National Standards and Applicable Codes
All appliances m u st b e installed in accordance w ith
the latest re v ision of the applica b le standards and
national codes. This refers also to the electric, gas
and
v enting installation. Note: Additional standards
for installations in p ub lic garages, aircraft hangars,
etc. may b e applica b le.
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.