background image

QUICK START GUIDE

en-9

DRIVING

1.

Release Brake

 - Make sure the Park 

Brake is released before you try to go 

forward or reverse.

2.

Forward 

- Carefully push the top (A) of 

the Forward / Reverse Foot Pedal to 

reach correct ground speed.

3.

Reverse

 - Carefully push the bottom (B) 

of the Forward / Reverse Foot Pedal to 

reach correct ground speed.

4.

To Stop

 - Carefully return the Forward/

Reverse Foot Pedal to the neutral 

position.

5. To hold the vehicle stopped on a slope 

it can be necessary to apply an amount 

of forward or reverse traction.

NOTE

:

Use complete foot to operate both 

forward and reverse. 

Unless in an emergency, do not move 

the pedal suddenly, always operate 

slowly and carefully.

Do not move the pedal with force from 

forward to reverse or reverse to 

forward.

The angle of the Foot Pedal can be 

altered to obtain the most comfortable 

angle for long periods of operation. This 

can be achieved by repositioning 

screws (D) as required.

Use complete foot to operate both 

forward and reverse.

The foot should always be kept firmly on 

the pedal to maintain full control of the 

drive pedal.

MOW/TRANSPORT SPEED SELECTOR

Limits the forward speed. To switch between 

Mow and Transport speeds move lever (C) 

left 

for Mow and

 right

 for Transport.

A

B

C

D

Содержание HR380





















Отзывы: