Ransomes HM600 Скачать руководство пользователя страница 44

Страница: 44 / 134

en-44

5 CONTROLS

5.2.Z.62

WARNING ENGINE FAULT __________________________________________

When this screen is shown, there is an engine fault.Stop the engine as soon as
possible and contact your service dealer.

When this fault occurs the machine go’s into limp-home mode.

Press the button below the



to confirm the fault.

5.2.Z.63

WARNING FOOT PEDAL FAULT _____________________________________

This screen is shown if there is a communications fault between the foot pedal
and the controller.

Stop the machine as soon as possible and contact your service dealer.

When this fault occurs the machine goes into limp-home mode.

Press the button below the



to confirm the fault.

5.2.Z.64

WARNING BATTERY FAULT _________________________________________

When this screen is shown, the battery is not charging or there is a charge
circuit fault.

Press the button below the



to confirm the fault.

5.2.Z.65

WARNING CHARGE FILTER BLOCKED________________________________

When this screen is shown, the hydraulic-charge filter is blocked and needs
replacing. Replace the filter element at the earliest opportunity to avoid
possible hydraulic system damage.

Press the button below the



to confirm the fault.

CHARGE FILTER

FAULT

Содержание HM600







































































































































Результаты поиска

Содержание HM600

Отзывы:

Похожие инструкции для HM600

Бренды по названию

Популярные бренды

Ransomes HM600, Безопасность, эксплуатация и обслуживание

Результаты поиска

Содержание HM600

Отзывы:

Похожие инструкции для HM600

Бренды по названию

Популярные бренды