background image

QUICK START GUIDE

en-12

MAIN RUN SCREEN

The main screen for operation gives the 
operator all the information necessary to 
operate the machine.  No operator input to 
view standard data is needed when you use 
the mower.
If an error occurs  when the operator has 
moved away from this screen, it immediately 
returns to this screen.
When a button is pressed, a bar is shown at 
the bottom of the screen to give more 
options.

Buttons numbered left to right.
Button 1: Screen Brightness and Contrast
Button 2: Up Arrow (Changes time, from 
hour meter to time of day)
Button 3: Down Arrow (Changes time, from 
time of day to hour meter)
Button 4: Enters the Menu structure.

If there are no more buttons pressed, the 
button bar disappears.

WATER TEMPERATURE SCREEN

If the temperature increases to 108°C, the 
RED LEDs (A) will  flash at a rate of two 
flashes every  four  seconds.  The warning 
buzzer will sound at the same rate and the 
“CLEAR BUGSCREEN” warning replaces 
the centre icons and flashes. Press the 
button under the checkmark to remove 
warning.  The RED LED’s will flash and the 
buzzer continues until the temperature has 
decreased to under 108°C.  When the 
temperature reaches 110°C, the lift / lower 
function is stopped and the power take off is 
disengaged.  The engine will shutdown at 
115°C.

This occurrence will also be recorded to 
memory, the data recorded is:
Water Temperature limit reached, Date, 
Time, Engine Hours, time above 110°C. 
Maximum temperature reached during the 
fault.

BLOCKED CHARGE FILTER SCREEN

This situation does not cause a fault until the 
hydraulic oil is at operating temperature. If 
the charge filter is blocked the icon will be 
shown, and the RED LED’s (A) will flash at a 
rate of a 1s flash every 5 seconds. The 
buzzer will sound at the same rate one 
second every 5 seconds.

The fault will also be recorded to memory, 
the data recorded is:
Blocked Charge Filter, Date, Time, Engine 
Hours, length of time engine continued to run 
after the fault occurred.

1234.5

1234.5

CLEAR BUGSCREEN

A

A

1234.5

BLOCKED CHARGE FILTER

FAULT

A

A

VISUAL DISPLAY

Содержание Highway 3

















Отзывы: