Rane CP 64 Скачать руководство пользователя страница 12

Страница: 12 / 12

Manual-12

©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com

…CP 64 Calibration (continued)

1. Connect the Power Supply and verify the

PWR

indicator lights.

2. Verify

Zone Level

controls are set to Maximum and that you have an active source for each of the Program Inputs you

intend to use. Select each

Program Input

and adjust its

Input Level

control to be the very loudest you would ever desire.

3. Adjust the rear panel

Zone Limit

thresholds so that they just start to audibly reduce the output level. This ensures that the

level in a Zone will never be louder than the maximum level you just set. If you wish one of the Zones to have a lower
maximum loudness, lower the

Zone Limit

threshold accordingly.

4. Turn the

Zone Level

controls down to a comfortable listening level.

5. Note that with the

Paging Zone Level

set to minimum, you will not hear the following Page. Speak very loudly (bark) into

the Paging Mic. Set the proper preamplifier gain by adjusting the

Page Trim

control (rear panel) so that the

Page

ver

oad Indicator (rear panel) just lights. It is important to set the gain of the pre-amp before setting the

Page Detect

Threshold

. Repeat for second Mic if used.

6. Speak into the Page Mic in a normal voice and adjust the

Page Detect Threshold

(rear panel) so the

Active

indicator (front

panel) lights only when you speak. If the

Page Detect Threshold

is set too low, the Pager may gate on due to background

sound. Repeat for second Mic if used.

7. With an active Program source playing in both Zones, speak into the Page Mic. Adjust the

Zone 1

and

Zone 2

Page Level

controls (front panel) to provide the correct Page-to-Program mix in each zone. If the

Page Detect Threshold

is set too

high, there may be a delay when you start to speak. To correct, lower the

Page Detect Threshold

setting. If a second Page

source is used, verify that it has the same level as the first Page source (it should be close). If not, use the

Page Trim

control of the second Page source to adjust its gain to match. If you change the gain of the second Page source substantially,
be sure to reset the

Page Detect Threshold

8. Set the

Ducker

switch to

. With an active Program source playing, speak into the Page Mic and adjust the

Ducker

Depth

as required. Repeat for both Zones.

9. Set the

Program Priority Assign

switch as required (on rear panel). If you do not require automatic priority program

override in a zone,

do not

assign it. Instead, use the front panel

Program Select

switch to select the “

” program Input as

you would any other non-priority input.

10. If remote control is used, select the appropriate

RMT

switch settings on the front panel and verify that the remotes function

correctly.

11. Adjust the Equalizers as required.

…You’re all set. Enjoy.

102907

Содержание CP 64













Результаты поиска

Содержание CP 64

Отзывы:

Бренды по названию

Популярные бренды

Rane CP 64, Руководство оператора

Результаты поиска

Содержание CP 64

Отзывы:

Бренды по названию

Популярные бренды