R&S ZNL Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 1135

background image

Getting Started

R&S

®

ZNL/ZNLE

50

User Manual 1178.5966.02 ─ 19

●

This connector is provided by the "Additional Interfaces" option R&S

FPL1-B5.

This option is not available for the R&S

ZNLE.

●

The headphones connector is only functional in Spectrum mode (option
R&S

ZNL3|4|6-B1).

It can

not

be used to output sounds that are generated via Windows audio APIs.

To hear those sounds, connect a USB audio device to the instrument or operate it
via remote desktop.

●

Interruptions in analog output can occur if you switch between a VNA and a spec-
trum application, due to the separate hardware. In particular, if you run a sequence
of measurements including both measurement types, switching between both
modes can interrupt the signal from the output connector.

Note the safety information provided in

"Using headphones"

For details, see the R&S

ZNL/ZNLE Spectrum mode user manual.

4.2.2.10

Sensor connector

The LEMOSA female connector is used to connect power sensors of the R&S

NRP-

Zxy family. For a detailed list of supported sensors, see the data sheet.

This connector is provided by the "Additional Interfaces" option R&S

FPL1-B5.

This option is not available for the R&S

ZNLE.

4.2.2.11

USB

The rear panel provides two additional female USB (3.0 standard) connectors to con-
nect external devices (see also

Chapter 4.2.2.11, "USB"

4.2.2.12

LAN

The R&S

ZNL/ZNLE is equipped with a 1

GBit Ethernet IEEE 802.3u network interface

with Auto-MDI(X) functionality. The assignment of the RJ-45 connector supports twis-
ted-pair category 5 UTP/STP cables in a star configuration (UTP stands for

unshielded

twisted pair

, and STP for

shielded twisted pair

).

For details, see

Chapter 8, "Network and remote settings"

4.2.2.13

DVI

You can connect an external monitor or other display device to the R&S

ZNL/ZNLE via

the DVI (Digital visual interface) connector to provide an enlarged display.

For details, see

Chapter 4.1.13, "Considerations for test setup"

Instrument tour

«
...
48
49
50
51
52
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

Бренд: OHAUS Страницы: 71

Бренд: Sensitech Страницы: 2

Panametrics XDP

Бренд: Baker Hughes Страницы: 64

Бренд: IROX Страницы: 8

Бренд: Z-Wave Страницы: 5

Бренд: Klein Tools Страницы: 20

Бренд: Charder Страницы: 12

Optical Power Expert

Бренд: EXFO Страницы: 93

Бренд: Georg Fischer Piping Systems Страницы: 45

Бренд: Toky Страницы: 15

Бренд: SDT Страницы: 2

Бренд: Futech Страницы: 68

Бренд: PASCO Страницы: 3

Бренд: JUMO Страницы: 24

Бренд: Lighthouse Worldwide Solutions Страницы: 84

Бренд: Hanna Instruments Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды