R&S ZNL Скачать руководство пользователя страница 446 | Manualshive

Страница: 446 / 1135

background image

VNA GUI reference

R&S

®

ZNL/ZNLE

446

User Manual 1178.5966.02 ─ 19

Note:

●

Circle limit check and display of limit circles are independent of each other:
–

The limit circles can be displayed, no matter if the circle limit check is enabled.

–

If "Limit Check" is enabled, the ripple limits are checked, no matter if they are
displayed.

●

If result evaluation is limited to a user-defined

Chapter 10.9.6,

"Circle Test tab"

on page 444 is only performed inside this display circle.

●

The circle limits can only be checked if the trace format is complex. While a carte-
sian format is active, the limit circles are hidden and the circle limit check is sus-
pended.

●

If the limit check for (cartesian)

is enabled, it is also evaluated in complex

diagrams.

Figure 10-12: Simultaneous dB Mag limit line and circle check

Remote command:

CALCulate<Chn>:LIMit:CIRCle[:STATe]
CALCulate<Chn>:LIMit:CIRCle:FAIL?
CALCulate:LIMit:CIRCle:FAIL:ALL?

Limit Fail Beep

Activates or deactivates the fail beep. The fail beep is a low-tone acoustic signal that is
generated each time the analyzer detects an exceeded limit. No fail beep can be gen-
erated if the limit check is switched off.

Note:

The R&S

ZNL/ZNLE does not have a built-in audio device and loudspeaker. To

hear sounds, connect a USB audio device to the instrument or operate it via remote
desktop.

Remote command:

CALCulate<Chn>:LIMit:CIRCle:SOUNd[:STATe]

Display Lines softtool

«
...
444
445
446
447
448
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: jenway Страницы: 20

Бренд: Unico Страницы: 10

Бренд: OHAUS Страницы: 84

Бренд: Vaisala Страницы: 2

Бренд: ZHYQ Страницы: 6

Бренд: Pangea Страницы: 2

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: UEi Страницы: 5

Бренд: WATERGUARD Страницы: 2

Бренд: kruss Страницы: 115

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

microCLIMA ULTRA

Бренд: MADDALENA Страницы: 17

Бренд: Benetech Страницы: 16

SensoControl ServiceJunior Series

Бренд: Parker Страницы: 148

Бренд: Stahl Страницы: 47

Бренд: Kawai Страницы: 2

Бренд: E+E Elektronik Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды