background image

Safety and regulatory information

R&S

®

QAT100

5

User Manual 1179.3073.02 ─ 02

1

 

Safety and regulatory information

The product documentation helps you use the product safely and efficiently. Follow the
instructions provided here and in the following chapters.

Intended use

The product is intended for the development, production and verification of electronic
components and devices in industrial, administrative, and laboratory environments.
Use the product only for its designated purpose. Observe the operating conditions and
performance limits stated in the data sheet.

Where do I find safety information?

Safety information is part of the product documentation. It warns you of potential dan-
gers and gives instructions on how to prevent personal injury or damage caused by
dangerous situations. Safety information is provided as follows:

In 

Chapter 1.1, "Safety Instructions"

on page 5. The same information is provi-

ded in many languages as printed "Safety Instructions". The printed "Safety
Instructions" are delivered with the product.

Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.

1.1

 

Safety Instructions

Products from the Rohde

 

&

 

Schwarz group of companies are manufactured according

to the highest technical standards. To use the products safely, follow the instructions
provided here and in the product documentation. Keep the product documentation
nearby and offer it to other users.

Use the product only for its intended use and within its performance limits. Intended
use and limits are described in the product documentation such as the data sheet,
manuals and the printed "Safety Instructions". If you are unsure about the appropriate
use, contact Rohde

 

&

 

Schwarz customer service.

Using the product requires specialists or specially trained personnel. These users also
need sound knowledge of at least one of the languages in which the user interfaces
and the product documentation are available.

Never open the casing of the product. Only service personnel authorized by
Rohde

 

&

 

Schwarz are allowed to repair the product. If any part of the product is dam-

aged or broken, stop using the product. Contact Rohde

 

&

 

Schwarz customer service at

http://www.customersupport.rohde-schwarz.com

.

Lifting and carrying the product

The maximum weight of the product is provided in the data sheet. To move the product
safely, you can use lifting or transporting equipment such as lift trucks and forklifts. Fol-
low the instructions provided by the equipment manufacturer.

Safety Instructions

Содержание QAT100













































Отзывы: