R&S NGE-K101 Скачать руководство пользователя страница 52

Страница: 52 / 105

Instrument Functions

R&S

NGE100B

User Manual 5601.1343.02 ─ 02

When the connection is alive, the LXI icon turns green on the status bar.

Table 5-13: Ethernet input field

Ethernet input field

Description

MAC Address

Shows the MAC address of this instrument.

Status

Shows if the connection is up or down.

IP Mode

Static & Manual: Manually configure an IP address
for the instrument.

DHCP & Auto-IP: Automatically assign an IP
address to the instrument.

IP Address

Address used in communication with the network.

Manually configure this field if IP Mode set to "Static
& Manual".

Subnet Mask

Secondary address used in communication with the
network.

Manually configure this field if IP Mode set to "Static
& Manual".

Default Gateway

Gateway address to connect to the network.

Manually configure this field if IP Mode set to "Static
& Manual".

LAN Reset

Restores the LAN settings to factory default.

It also removes the LXI web password.

Apply

Apply static IP settings.

5.6.1.2

Wireless Connection

R&S NGE-K102 (order number: 5601.2210.03) option is required to connect the R&S
NGE100B to a network via WLAN connection.

WLAN connection

The LAN connection has a higher priority over WLAN.
If LAN is connected, the WLAN connection will be disconnected. When LAN is discon-
nected, WLAN will reconnect automatically.

1. Select "Interface > WLAN" menu item.

The R&S NGE100B displays the "WLAN" dialog. See

Figure 5-21

Connecting to a Network

www.allice.de

Allice Messtechnik GmbH

Содержание NGE-K101










































































































Результаты поиска

Содержание NGE-K101

Отзывы:

Бренды по названию

Популярные бренды

R&S NGE-K101, Руководство пользователя

Результаты поиска

Содержание NGE-K101

Отзывы:

Бренды по названию

Популярные бренды