R&G LGFK0023 Скачать руководство пользователя страница 9

Page 

9

 of 

9

 

LGFK0023

 

 

R&G 

Unit 

1

, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ

 

Tel: +44 (0)

1

420 89007  Fax: +44 (0)

1

420 87301  

www.rg-racing.com

  Email: 

[email protected]

 

 

 
 
 
DES MOTORRADES NICHT BEEINFLUSST ODER GEFÄHRDET. DIE FUNKTION UND FESTIGKEIT MUSS 
REGELMÄSSIG ÜBERPRÜFT WERDEN. 
 
DIE  NICHTBEACHTUNG  DIESES  SICHERHEITSHINWEISES  KANN  ZU  SCHWEREN  VERLETZUNGEN 
ODER BESCHÄDIGUNG FÜHREN.  

 
 

AUSGABE 1 - 15/07/2019 (FB) 

 
 

CONSUMER NOTICE 

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance 
or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given 
or will apply to 

the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of me

rchantable quality and suitable 

for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the 

workmanship has been disturbed.  The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any 
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or 

maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good

 engineering practice or if the defect arises from accident or neglect. Other than 

identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable  for indirect or consequential loss and otherwise its 
liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms 

do not affect the Buyer’s statutory rights.

 

R&G RACING RETURNS POLICY (NON-FAULTY GOODS) 

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer 
must prove if necessary).  Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% 
restocking and handling fee (25% of the gross value exc. P&P 

 at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns 

of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods. 

 

Содержание LGFK0023










Отзывы: