Ramsey Winch RPH 8000T Скачать руководство пользователя | Manualshive

Страница: 5 / 24

background image

4

HYDRAULIC SYSTEM REQUIREMENTS

Refer to the performance charts below to properly match your hydraulic system to the winch performance. The
charts consist of: (1) line pull (LB) first layer vs. working pressure (PSI), and (2) line speed, first layer (FPM) vs. flow
(GPM). A cylinder spool directional control valve is recommended.

*CAUTION: DO NOT EXCEED 20 GPM. IF EXCEEDED, MOTOR AND WINCH MAY BE DAMAGED.

PERFORMANCE

CHARTS*

SYSTEM REQUIREMENTS:

2500 PSI RELIEF VALVE SETTING

15 GPM FLOW RATE*

10 MICRON NORMAL FILTRATION

1000 PSI MAXIMUM BACK PRESSURE

EMERGENCY STOP VALVE

Installer must determine type of emergency
stop required. A manual control valve also
serves as an emergency stop valve. An
emergency stop valve may be required with
other types of control valves.

«
...
3
4
5
6
7
...
»

Содержание RPH 8000T

























Отзывы:

Нет отзывов

Похожие инструкции для RPH 8000T

Бренд: Hamron Страницы: 26

Бренд: BRADEN Страницы: 35

Бренд: Harken Страницы: 59

Бренд: Harken Страницы: 4

DeckHand DH 25R

Бренд: MINN KOTA Страницы: 5

Бренд: Allied Страницы: 112

Бренд: ZEAK Страницы: 16

Бренд: Harken Страницы: 2

Бренд: Harken Страницы: 32

Бренд: Ramsey Winch Страницы: 36

Chicago Electric Power Tools 40124

Бренд: Harbor Freight Tools Страницы: 12

Бренд: Thaler Страницы: 28

Бренд: Pulley-man Страницы: 38

Бренд: Central Forge Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды