background image

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 

RAMSEY WINCH COMPANY

 

Post Office Box 581510  Tulsa, Oklahoma 74158-1510 
Telephone: (918) 438-2760   FAX: (918) 438-6688 

 

  

OM914002-0802-F 

 

LIMITED WARRANTY

 

RAMSEY WINCH warrants each new RAMSEY Winch to be free from defects in material and workmanship 
for a period of one (1) year from date of purchase.

 

 

The obligation under this warranty, statutory or otherwise, is limited to the replacement or repair at the 
Manufacturer's factory, or at a point designated by the Manufacturer, of such part that shall appear to the 
Manufacturer, upon inspection of such part, to have been defective in material or workmanship. 

 

 

This warranty does not obligate RAMSEY WINCH to bear the cost of labor or transportation charges in 
connection with the replacement or repair of defective parts, nor shall it apply to a product upon which 
repair or alterations have been made, unless authorized by Manufacturer, or for equipment misused, 
neglected or which has not been installed correctly.

 

 

RAMSEY WINCH shall in no event be liable for special or consequential damages.  RAMSEY WINCH 
makes no warranty in respect to accessories such as being subject to the warranties of their respective 
manufacturers.

 

 

RAMSEY WINCH, whose policy is one of continuous improvement, reserves the right to improve its 
products through changes in design or materials as it may deem desirable without being obligated to 
incorporate such changes in products of prior manufacture.

 

 

If field service at the request of the Buyer is rendered and the fault is found not to be with RAMSEY 
WINCH's product, the Buyer shall pay the time and expense to the field representative.  Bills for service, 
labor or other expenses that have been incurred by the Buyer without approval or authorization by 
RAMSEY WINCH will not be accepted

 

See warranty card for details.

 

 

Содержание RPH 12,000

























Отзывы: