background image

SYMPTOM 

POSSIBLE PROBLEMS   SERVICE

Power/Exhaust Stage of Operation 

— Tool operates properly,  — Battery cell is  

— Charge Battery Cell 

  but fasteners do not     discharged 

  drive fully
   

— Fuel Cell is low 

— Check Fuel Cell according to  

   

   

  Operating Manual and replace  

   

   

  as required.

   

— There may be loss of    — Press Work Contact Element  

   

  seal in combustion 

  against workpiece for one minute. 

   

    chamber 

   Pull trigger. If fastener does not 

   

   

  drive, there is a leak that requires  

   

   

  service.  

— Tool operates  

— Fuel Cell is low 

— Check Fuel Cell according to 

  erratically or appears        

  Operating Manual 

  to be losing power—     

 

   tool LED is green

 

— Filter element is dirty,    — Remove Filter element and clean  

   

  causing tool to overheat   according to Operating Manual.  

   

   

  Use safe cleaning solution 

   

   

  to remove stubborn debris.

   

— Tool Sleeve or   

— Clean tool per Cleaning Procedure 

   

  O-Rings are dirty

Returning/Purging Stage of Operation 

— Tool operated and  

— Built-up dirt and    

— Clean Piston and Nose bore with  

  drove fastener, but   

  debris on Piston  

  safety solvent. See Cleaning  

  piston did not return 

  

or in Nose bore 

  Procedure.

  to start position 

— Mushrooming of

 

— Contact Ramset Distributor 

   

  Piston Tip 

  Sales Representative for service.

   

— Exhaust ports on the    — Return tool to Authorized  

   

  Sleeve are dirty 

  Ramset Distributor Sales 

   

  or clogged.  

  Representative for service. 

   

— Tool (Sleeve) or   

— Clean tool per Cleaning Procedure 

   

  O-Rings are dirty 

— Tool does not open  

— Work Contacting   

— Clean tool or replace Work  

  after tool fires 

  Element is bent, 

  Contacting Element as required. 

   

  or tool is dirty 

 

   

    

If the T3SS or T3 Magazine tool will not operate after following the  

above service directions, return the tool to an Ramset  

Distributor Sales Representative for service.

 

SERVICING / TROUBLESHOOTING

SERVICING / TROUBLESHOOTING 

14

Содержание T3SS

















Отзывы: