RAMMER RPV22R Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 80

background image

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Page 18 - Operation

Safety

RPV14R, RPV22R, RPV29R, RPV39R, RPV53R, RPV75R

COLLAPSING CONCRETE FRAMES

Protect yourself and your surroundings from collapsing concrete frames. Do not
operate the product or carrier with people around it.

PRODUCT LIMITS

Operating the product beyond its design limits can cause damage. It can also be
dangerous. See “Product specifications” on page 64.

Do not try to upgrade the product's performance by unapproved modifications.

HYDRAULIC FLUID

Fine jets of hydraulic fluid at high pressure can penetrate the skin. Do not use your
fingers to check for hydraulic fluid leaks. Do not put your face close to suspected
leaks. Hold a piece of cardboard close to suspected leaks and then inspect the
cardboard for signs of hydraulic fluid. If hydraulic fluid penetrates your skin, seek
medical help immediately.

Hot hydraulic fluid can cause severe injuries.

HYDRAULIC HOSES AND FITTINGS

Ensure all hydraulic components will withstand maximum pressure and mechanical
stresses caused by operation of the product. Consult your local dealer for
instructions.

G0100

3

1

«
...
16
17
18
19
20
...
»

Содержание RPV22R

















































































Отзывы:

Нет отзывов

Похожие инструкции для RPV22R

Бренд: Campden instruments Страницы: 8

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренд: DBX Bushido Страницы: 12

Бренд: Hammer Страницы: 42

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: SandenVendo Страницы: 19

Team Agile Color Tune TM16-0

Бренд: GRAU Страницы: 24

Бренд: Milestone Страницы: 64

Бренд: Bodyworx Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды