RAM 1500 2023 страница 186 Скачать руководство пользователя

Страница: 186 / 416

184

STARTING AND OPERATING

OWING

IPS

Before towing, practice turning, stopping, and backing up

the trailer in an area located away from heavy traffic.

Automatic Transmission

The DRIVE range can be selected when towing. The

transmission controls include a drive strategy to avoid

frequent shifting when towing. However, if frequent

shifting does occur while in DRIVE, select TOW/HAUL

mode or select a lower gear range (using the Electronic

Range Select (ERS) shift control).

NOTE:

Using TOW/HAUL mode or selecting a lower gear range

(using the ERS shift control) while operating the vehicle

under heavy loading conditions will improve performance

and extend transmission life by reducing excessive

shifting and heat build up. This action will also provide

better engine braking.

Tow/Haul Mode

To reduce potential for automatic transmission

overheating, activate TOW/HAUL mode when driving in

hilly areas, or select a lower gear range (using the (ERS)

shift control) on more severe grades.

Cruise Control — If Equipped



Do not use on hilly terrain or with heavy loads.



When using the Cruise Control, if you experience speed

drops greater than 10 mph (16 km/h), disengage until

you can get back to cruising speed.



Use Cruise Control in flat terrain and with light loads to

maximize fuel efficiency.

Air Suspension System

To aid in attaching/detaching the trailer from the vehicle,

the air suspension system can be used

page 134.

Selecting Tow/Haul or connecting a trailer with an

Integrated Trailer Brake Module (ITBM) will disable

Automatic Aero mode to avoid height changes while

towing and shifting loads or tongue weights.

NOTE:

The vehicle must remain in the engine running position

while attaching a trailer for proper leveling of the air

suspension system.

SNOWPLOW

Snowplow Prep Packages are available as a factory

installed option. These packages include components

necessary to equip your vehicle with a snowplow.

NOTE:

Before installation of a snowplow it is highly recom

mended that the owner/installer obtain and follow the

recommendations contained within the current Body

Builder’s Guide. See an authorized dealer, installer or

snowplow manufacturer for this information. There are

unique electrical systems that must be connected to

properly ensure operator safety and prevent overloading

vehicle systems.

WARNING!

Attaching a snowplow to this vehicle could adversely

affect performance of the airbag system in a collision.

Do not expect that the airbag will perform as described

earlier in this manual.

CAUTION!

The “Lamp Out” indicator could illuminate if exterior

lamps are not properly installed.

23_DT_OM_EN_USC_t.book Page 184

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды

RAM 1500 2023, Руководство пользователя

Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды