manualshive.com logo in svg

RAM 1500 2023, Руководство пользователя, Страница: 136 / 416

Поделиться
Скачать
RAM 1500 2023 Скачать руководство пользователя страница 136

134

STARTING AND OPERATING

 

Shifting Procedure

If any of the requirements to select a new transfer case 

position have not been met, then the transfer case will 

not shift. The position indicator light for the previous 

position will remain on and the newly selected position 

indicator light will continue to flash until all the require

-

ments for the selected position have been met.

If all the requirements to select a new transfer case 

position have been met, then the current position

indicator light will turn off and the selected position 

indicator light will flash until the transfer case 

completes the shift. When the shift is complete, the 

position indicator light for the selected position will 

stop flashing and remain on.

ACTIVE-LEVEL FOUR CORNER AIR 

SUSPENSION SYSTEM — IF EQUIPPED  

D

ESCRIPTION

The air suspension system provides full-time load-leveling 

capability along with the benefit of being able to adjust 

vehicle height by using the toggle switch.

Air Suspension Switch

Off-Road 2 (OR2) (Raises the vehicle approximately 

2 inches [51 mm]) – This position is intended for 

off-road use only where maximum ground clearance is 

required. To enter OR2, push the height selector switch 

up twice from the NRH position or once from the OR1 

position while vehicle speed is below 20 mph 

(32 km/h). While in OR2, if the vehicle speed exceeds 

25 mph (40 km/h) the vehicle height will be automati

-

cally lowered to OR1. Off-Road 2 may not be available 

due to vehicle payload, an instrument cluster message 

is displayed when this occurs  

Ú

page 98.

Off-Road 1 (OR1) (Raises the vehicle approximately 

1 inch [26 mm]) – This position should be the primary 

position for all off-road driving until Off-Road 2 (OR2) is 

needed. A smoother and more comfortable ride will 

result. To enter OR1, push the height selector switch up 

once from the NRH position while the vehicle speed is 

below 35 mph (56 km/h). When in the OR1 position, if 

the vehicle speed remains between 40 mph (64 km/h) 

and 50 mph (80 km/h) for greater than 20 seconds or 

if the vehicle speed exceeds 50 mph (80 km/h), the 

vehicle will be automatically lowered to NRH. 

Off-Road 1 may not be available due to vehicle 

payload, an instrument cluster message is displayed 

when this occurs  

Ú

page 98.

Normal Ride Height (NRH) – This is the standard posi

-

tion of the suspension and is meant for normal driving.

Aero Height (Lowers the vehicle approximately 0.6 inch 

[15 mm]) – This position provides improved aerody

-

namics by lowering the vehicle. The vehicle will auto

-

matically enter Automatic Aero Mode when the vehicle 

speed remains between 62 mph (100 km/h) and 

66 mph (106 km/h) for greater than 20 seconds or if 

the vehicle speed exceeds 66 mph (106 km/h). 

1 — Off-Road 2 Indicator (Customer Selectable)
2 — Off-Road 1 Indicator (Customer Selectable)
3 — Normal Ride Height Indicator (Customer Selectable)
4 — Aero Height Indicator (Customer Selectable)
5 — Entry/Exit Height Indicator (Customer Selectable)

CAUTION!

If the vehicle is in Off-Road 1 or Off-Road 2 setting, be 

aware of your surroundings, you may not have the 

clearance required for certain areas and vehicle 

damage may occur.

23_DT_OM_EN_USC_t.book  Page 134  

Содержание 1500 2023

































































































































































































































































































































































































































Отзывы:

Нет отзывов