1
CONTROLLERS
3
2
1
4
5
10
6
9
8
7
3
2
1
4
5
10
6
9
8
7
3
2
1
4
5
10
6
9
8
7
Set-Up
•Place in a convenient location avoiding any moisture or chemicals.
•All components should be connected prior to turning on the main power switch (#3).
•Make sure the power cord is securely attached in the rear (#1).
•Controllers utilize a state of the art microprocessor chip for programming of speed
control, overload and safety and much more. This includes a memory feature to
remember the last user settings before the main power is turned off.
•Turn off the main power switch when not in use to avoid power and electric current to
the controller.
•Always check the handpiece carefully for smooth operation prior to each use.
•Do not use with any other brands of equipment as brushless units are not compatible
with other brands.
Power Outlet:
Main power cord receptacle. The power cord is plugged here.
Warning: The control box is designed for one Input AC voltage only. Make sure that the
available electrical power is compatible with the voltage input requirement of the
control box. Refer to assembly #2.
1
110/230V:
Switch from 110 volts or 230 volts.
2
Main Power Switch:
Turns the control box on and off. Switch should be in the “off”
position when not in use.
3
Foot Switch Control Outlet:
The foot pedal cord plugs in here, either the on/off or
variable speed foot controller.
4
Handpiece Cord Outlet:
The handpiece cord plugs in here.
5
Operation Indicator:
LED speed display and error alerts.
6
Speed Control Dial:
0-35,000rpm or 0-45,000rpm. Used to adjust or vary the desired
speed. In hand mode, turn the dial clockwise to increase the speed and counterclockwise
to reduce the speed. While using in foot pedal mode, the speed dial setting can also limit
the top or maximum speed for greater control and safety.
7
Hand/Foot Button:
When set in the hand position, the hand indicator light will turn on,
the speed is completely controlled by the speed dial knob. when set in the foot pedal
mode, the foot indicator light will turn on, the speed is controlled by the settings of the
knob when using the on/off pedal and the speed is completely variable when using the
variable foot pedal.
8
Motor Button:
Engages the handpiece for operation and use or can disengage for
stopping or taking a rest from operation while remaining ready.
9
Forward/Reverse Button:
Controls handpiece direction to forward or reverse.
10
Model Input Output MaxAmp Rotate Speed Power L W H Wt.
iCUBE
AC110V/230V
50HZ-60HZ
DC0-32V
2A
0-35,000rpm/
0-45,000rpm
50W
5”
4”
4 1/2”
3.8lbs
MICROLAB
AC110V/230V
50HZ-60HZ
DC0-32V
2A
0-35,000rpm/
0-45,000rpm
60W
8”
4”
6”
4.4lbs
RAMPOWER
AC110V/230V
50HZ-60HZ
DC0-32V
2A
0-35,000rpm/
0-45,000rpm
60W
6”
3 1/4”
5 1/4”
4.4lbs
Standard
2
Assembly
1. Handpiece cord plugs into the lower middle socket(#5).
2. Foot Pedal plugs into the lower middle socket(#4).
3. Plug the power cord to an electrical outlet. Make sure that the outlet is properly
grounded and compatible to the voltage input requirement:
NOTE: Please make sure that the power switch is in “off” position before plugging the
power cord to an electrical outlet. The speed control must be set to minimum and check
thevoltage switch selection to be sure it is set at the proper voltage either 110 or 230 volts.
4. Turn the power switch (#3) to “on” position. The LED display (#6) should appear.
5. The handpiece is now ready for operation. Press Hand/Foot Button (#8)
a. HAND MODE - Hand indicator light should glow. The speed of the motor
is set by turning the control knob clockwise.
b. FOOT CONTROL MODE - Foot indicator light should glow.
•With the On/Off foot pedal, step on the foot pedal and gradually turn
the speed control knob clockwise until the desired speed is attained.
•With the variable foot pedal, gradually step on the pedal until the
desired speed is attained.
