RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 486 / 542

background image

Fluid Level Check

This fluid level can be checked by removing the filler plug.
The fluid level should be to the bottom edge of the filler
plug hole with the vehicle in a level position.

Automatic Transmission — If Equipped

Selection Of Lubricant

It is important to use the proper transmission fluid to
ensure optimum transmission performance and life. Use
only the manufacturer’s specified transmission fluid. Refer
to “Fluids, Lubricants, And Genuine Parts” in this section
for fluid specifications. It is important to maintain the
transmission fluid at the correct level using the recom-
mended fluid. No chemical flushes should be used in any
transmission; only the approved lubricant should be used.

CAUTION!

Using a transmission fluid other than the manufactur-
er’s recommended fluid may cause deterioration in
transmission shift quality and/or torque converter
shudder, and will require more frequent fluid and
filter changes. Refer to “Fluids, Lubricants, And Genu-
ine Parts” in this section for fluid specifications.

Special Additives

The manufacturer strongly recommends against using any
special additives in the transmission. Automatic Transmis-
sion Fluid (ATF) is an engineered product and its perfor-
mance may be impaired by supplemental additives. There-
fore, do not add any fluid additives to the transmission.
Avoid using transmission sealers as they may adversely
affect seals.

CAUTION!

Do not use chemical flushes in your transmission as
the chemicals can damage your transmission compo-
nents. Such damage is not covered by the New Vehicle
Limited Warranty.

Fluid Level Check

Check the fluid level when the engine is fully warmed up
and the transmission fluid is at normal operating tempera-
ture. Driving with an improper fluid level will greatly
reduce the life of the transmission and of the fluid. Check
the fluid level whenever the vehicle is serviced.

484

MAINTAINING YOUR VEHICLE

«
...
484
485
486
487
488
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Fabbri Страницы: 4

Бренд: TATA Motors Страницы: 236

Бренд: STARLANE Страницы: 24

Бренд: UAZ Страницы: 112

Бренд: r.LiNK Страницы: 21

Бренд: Thule Страницы: 4

Бренд: Hyundai Страницы: 168

Бренд: Seat Страницы: 300

Бренд: Blue Ox Страницы: 5

Бренд: Whelen Engineering Company Страницы: 4

Бренд: Oldsmobile Страницы: 340

Бренд: pewag Страницы: 52

ProPlus 620066V01

Бренд: PAT Страницы: 13

PerfectView CRT300

Бренд: Waeco Страницы: 200

Бренд: ULTIMATE SPEED Страницы: 18

Бренд: AdvanceTec Страницы: 8

Бренд: AdvanceTec Страницы: 12

Бренд: AdvanceTec Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды