RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 356 / 542

background image

If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.

NOTE:

•

Increased noise levels at the end of the steering wheel
travel are considered normal and do not indicate that
there is a problem with the power steering system.

•

Upon initial start-up in cold weather, the power steering
pump may make noise for a short amount of time. This
is due to the cold, thick fluid in the steering system. This
noise should be considered normal, and it does not in
any way damage the steering system.

CAUTION!

Prolonged operation of the steering system at the end
of the steering wheel travel will increase the steering
fluid temperature and it should be avoided when
possible. Damage to the power steering pump may
occur.

Power Steering Fluid Check

Checking the power steering fluid level at a defined service
interval is not required. The fluid should be checked at
every oil change if a leak is suspected, abnormal noises are
apparent, and/or the system is not functioning as antici-
pated. Coordinate inspection efforts through an authorized
dealer.

WARNING!

Fluid level should be checked on a level surface and
with the engine off to prevent injury from moving
parts and to ensure accurate fluid level reading. Do not
overfill. Use only manufacturer’s recommended power
steering fluid.

CAUTION!

Do not use chemical flushes in your power steering
system as the chemicals can damage your power steer-
ing components. Such damage is not covered by the
New Vehicle Limited Warranty.

If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all

354

STARTING AND OPERATING

«
...
354
355
356
357
358
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Hama Страницы: 2

Бренд: Abarth Страницы: 36

Бренд: Daihatsu Страницы: 340

Бренд: Jeep Страницы: 6

Бренд: Back View Страницы: 168

Бренд: TATA Motors Страницы: 161

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

Бренд: Mobis Страницы: 16

Бренд: Subaru Страницы: 216

2013 C-Class Coupe

Бренд: Mercedes-Benz Страницы: 388

Бренд: Standby Страницы: 10

Бренд: Ford Страницы: 37

Бренд: hc-cargo Страницы: 60

Бренд: AEM Страницы: 27

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: J. Strong Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды