RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 32 / 542

background image

•

The engine can be started two consecutive times (two
15-minute cycles) with the key fob. However, the igni-
tion must be placed in the ON/RUN position before you
can repeat the start sequence for a third cycle.

To Exit Remote Start Mode Without Driving The
Vehicle

Push and release the Remote Start button one time or allow
the engine to run for the entire 15-minute cycle.

NOTE:

To avoid unintentional shut downs, the system will

disable the one time push of the Remote Start button for
two seconds after receiving a valid Remote Start request.

To Exit Remote Start Mode And Drive The Vehicle

Before the end of the 15-minute cycle, push and release the
unlock button on the key fob to unlock the doors and
disarm the vehicle security alarm system (if equipped).
Then, prior to the end of the 15-minute cycle, cycle the
ignition to the ON/RUN position.

Remote Start Comfort Systems — If Equipped

When Remote Start is activated, the heated steering wheel
and driver heated seat features will automatically turn on
in cold weather. In warm weather, the driver vented seat
feature will automatically turn on when the remote start is

activated. These features will stay on through the duration
of Remote Start or until the ignition switch is turned to the
ON/RUN position.

The Remote Start Comfort System can be activated and
deactivated through the Uconnect System. Refer to
“Uconnect Settings” in “Understanding Your Instrument
Panel” for further information on Remote Start Comfort
System operation.

General Information

The following regulatory statement applies to all Radio
Frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired opera-
tion.

NOTE:

Changes or modifications not expressly approved

by the party responsible for compliance could void the
user’s authority to operate the equipment.

30

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
30
31
32
33
34
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

CK 3000 Evolution

Бренд: Parrot Страницы: 2

MagicComfort MSH200

Бренд: Waeco Страницы: 108

Бренд: Tusk Страницы: 2

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Fast Master Products Страницы: 13

Бренд: Vauxhall Страницы: 259

Бренд: Toyota Страницы: 600

Бренд: Volvo Страницы: 211

Бренд: GAC MOTOR Страницы: 356

Бренд: OHIOSTEEL Страницы: 2

Бренд: Guardsman Страницы: 2

Бренд: Mercedes-Benz Страницы: 24

Бренд: BMW Страницы: 242

Бренд: HawksHead Страницы: 10

Бренд: Jotto Desk Страницы: 3

Бренд: Geely Страницы: 188

Бренд: Honda Страницы: 358

Бренд: Toyota Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды