Rally RA13538B Скачать руководство пользователя страница 21

21

SERVICE AND ADJUSTMENTS

WARNING:  TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER-
 VICE OR AD JUST MENTS:

1.   Depress clutch/brake pedal fully and set parking brake.
2.   Place gearshift lever in neutral (N) position.
3.   Place attachment clutch  in “DISENGAGED” position.
4.   Turn ignition key to “STOP” and remove key.
5.   Make sure the blades and all moving parts have completely stopped.
6.   Disconnect spark plug wire from spark plug and place wire where it cannot 

come in contact with plug.

TRACTOR

TO REMOVE MOWER 

Mower will be easier to remove from the 
right side of tractor.
1.   Place attachment clutch in “DIS EN-

GAGED” position.

2.   Move attachment lift lever forward to 

low er mower to its lowest po si tion.

3.   Roll belt off engine pulley.
4.   Remove small retainer spring, and 

remove clutch spring off pulley bolt.

5.   Remove large retainer spring, slide 

col lar off and push housing guide out 
of brack et.

6.   Disconnect anti-sway bar from chas sis 

bracket by re mov ing re tain er spring.

7.   Disconnect suspension arms from rear 

deck brackets by removing re tain er 
springs.

8.   Disconnect front links from deck by 

re mov ing retainer springs.

9.   Raise lift lever to raise suspension 

arms. Slide mower out from under trac-
tor.

IMPORTANT:

 If an attachment oth er than 

the mower deck is to be mounted on the 
trac tor, remove the front links and hook 
the clutch spring Into square hole in frame.

TO INSTALL MOWER 

1.   Raise attachment lift lever to its high est 

position.

2.   Slide mower under tractor with defl ec-

tor shield to right side of tractor.

3.   Lower lift lever to its lowest po si tion.
4.   Connect front links to mower deck and 

secure with retainer springs.

5.   Connect suspension arms to rear 

deck brackets and secure with retainer 
springs.

38

42

02695

Suspension 
Arms

Retainer 
Spring

Anti-Sway 
Bar

Housing 
Guide

Collar

Large Re tain er 
Spring

Clutch 
Spring

Small Retainer 
Spring

Bracket

Retainer Springs
(Both Sides)

Front Link

Engine 
Pulley

Square Hole

Defl ector Shield

Small Retainer 
Spring

Clutch Spring

Flat Washer

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание RA13538B

































Отзывы: