manualshive.com logo in svg

Rally AG15538A, Руководство пользователя

Поделиться
Скачать
Rally AG15538A Скачать руководство пользователя страница 24

24

Retaining 
Ring

Washers

Square Key
(Rear Wheel Only)

Axle 
Cover

FRONT WHEEL TOE-IN/CAM BER

The front wheel toe-in and camber are not 
adjustable on your tractor.  If dam age has 
occurred to affect the front wheel toe-in or 
camber, contact your nearest authorized 
service center/de part ment. 

TO AD JUST STEER ING WHEEL ALIGN-
 MENT

If steering wheel crossbars are not 
hor i zon tal (left to right) when wheels are 
positioned straight forward, remove steer-
 ing wheel and reassemble with crossbars 
horizontal. Tighten securely.

TO REMOVE WHEEL FOR REPAIRS 

1.   Block up axle securely.
2.   Remove axle cover, retaining ring and 

washers to allow wheel removal (rear 
wheels have a square key - Do not 
lose).

3.   Repair tire and reassemble.

NOTE:

 On rear wheels only:  align 

grooves in rear wheel hub and axle.  Insert 
square key.
4.   Replace washers and snap retaining 

ring securely in axle groove.

5.   Replace axle cover.

NOTE: 

To seal tire punctures and pre vent 

fl at tires due to slow leaks, tire sealant 
may be purchased from your local parts 
dealer. Tire sealant also pre vents tire dry 
rot and corrosion.

Center 
Span
Keeper

Transaxle 
Pulley

Stationary 
Idler

Clutching 
Idler

Engine 
Pulley

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface.  En gage 
parking brake.  For as sis tance, there is a 
belt installation guide decal on bottom side 
of left footrest.

BELT REMOVAL -
1.   Remove mower (See “TO RE MOVE 

MOWER” in this section of manual).

NOTE:

 Observe entire motion drive belt 

and position of all belt guides and keepers.
2.   Remove belt from stationary idler and 

clutching idler.

3.   Remove belt downward from around 

en gine pulley.

4.   Pull belt slack toward rear of trac tor.  

Remove belt upwards from transaxle 
pulley by de fl ect ing belt keepers.

5.   Remove belt from center span keeper 

and pull belt away from tractor.

BELT INSTALLATION -
1.   Carefully work new belt down be tween 

transaxle belt keepers and onto the 
input pulley.

2.   Slide belt into the center span keeper.
3.   Pull belt toward front of tractor and roll 

around the top groove of engine pulley.

4.   Install belt through stationary idler and 

clutch ing idler.

5.   Make sure belt is in all pulley grooves 

and in side all belt guides and keep ers.

6.   Install mower (See “TO IN STALL 

MOWER” in this sec tion of manual).

Get other manuals https://www.bkmanuals.com

Содержание AG15538A

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды