Raisecom RCMS2902-2E1GE-BL Скачать руководство пользователя страница 14

Страница: 14 / 33

Raisecom
RCMS2902-2E1GE-BL Product Description

3 Card appearance and descriptions

Raisecom Technology Co., Ltd.

LED

Status

Description

LOS

Red

Loss Of Signal (LOS) alarm LED



Red: optical signals received by the local optical interface are
lost.



Blinking red: optical signals received by the remote optical
interface are lost.



Off: optical signals received by the optical interface are
normal.

Green

Ethernet interface working mode LED



Green: the device is working in 1000 Mbit/s mode.



Off: the device is working in 100 Mbit/s mode or stops
working.

LNK/ACT

Green

Ethernet interface working LED



Green: the Ethernet interface is connected properly.



Blinking green: the Ethernet interface is properly connected
is receiving or sending data.



Off: the Ethernet interface is connected improperly.

1000M

Green

Ethernet interface working speed LED



Green: the Ethernet interface speed is 1000 Mbit/s.



Off: the Ethernet interface speed is 100 Mbit/s or the Ethernet
interface is not working.

L/R

LOS(1-2)

Red

E1 tributary Rx signal LOS alarm LED



Red: a LOS alarm is generated on the local E1 tributary.



Blinking red: a LOS alarm is generated on the remote E1
tributary.



Off: no LOS alarm is generated on the local and remote E1
tributaries.



When an alarm is generated on both the local and remote devices, the alarm on
the local device is displayed first.



Only in E1 framed mode, the alarm on the remote device can be displayed on the
local device.

3.3 Interfaces

Table 3-2 describes interfaces on the RCMS2902-2E1GE-BL.

Table 3-2

Interfaces on the RCMS2902-2E1GE-BL

Interface

Type

Description

RJ45

One GE Ethernet electrical interface

2E1

RJ45

One E1 balanced interface for transmitting 2-way balanced
E1 services

Содержание RCMS2902-2E1GE-BL


































Результаты поиска

Содержание RCMS2902-2E1GE-BL

Отзывы:

Похожие инструкции для RCMS2902-2E1GE-BL

Бренды по названию

Популярные бренды

Raisecom RCMS2902-2E1GE-BL, Описание продукта

Результаты поиска

Содержание RCMS2902-2E1GE-BL

Отзывы:

Похожие инструкции для RCMS2902-2E1GE-BL

Бренды по названию

Популярные бренды