Raisecom P100R001 Скачать руководство пользователя страница 177

Страница: 177 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

152

Table 10-28

LEDs on the FE16E1 card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

100M

Green

FE electrical interface rate LED:



Green: the FE electrical interface is working at 100
Mbit/s.



Off: the FE electrical interface is working at 10 Mbit/s.

LNK/ACT

Green

Link working LED



Green: the link interface is working properly.



Off: the link interface is disconnected or is working
improperly.



Blinking green: the link interface is receiving or sending
data.

FDX

Green

Duplex mode LED



Green: the FE electrical interface is working in full duplex
mode.



Off: the FE electrical interface is working in half duplex
mode.

10.5.6 DIP switch

Table 10-29 lists configurations of the DIP switch on the FE16E1 card.

Table 10-29

Configurations of the DIP switch on the FE16E1 card

SW1

Function

Status

Description

KEY1

Configure
default
aggregation
mode for data.

OFF

Aggregating data to the FE electrical interface on
the front panel

Aggregating data to the Ethernet switching card
through the backplane

KEY2

Reserved

–

SW2 on the DIP switch is the global reset button. Press it with caution, because this
restarts the RC3000-15 globally.

Содержание P100R001


















































































































































































































































































Результаты поиска

Содержание P100R001

Отзывы:

Похожие инструкции для P100R001

Бренды по названию

Популярные бренды

Raisecom P100R001, Описание аппаратуры

Результаты поиска

Содержание P100R001

Отзывы:

Похожие инструкции для P100R001

Бренды по названию

Популярные бренды