Raisecom iTN8600-I страница 35 Скачать руководство пользователя

Страница: 35 / 71

Raisecom
iTN8600-I (A) Product Description

4 Technical specifications

Raisecom Proprietary and Confidential

Parameter

Description

Operating temperature (º

C) (altitude:

0–1800 m)

-5 to 50

Operating humidity (relative
humidity)

10%–90% (indoor), non-condensing

Lightning protection on the DC power
interface



2 kV in differential mode



4 kV in common mode

Lightning protection on the AC power
interface



2 kV in differential mode



4 kV in common mode

Noise



Telecom equipment room: 72–75 dB (A)



Manned equipment room: the A-weighted
sound power-level Lwad of the entire device is
7.2 Bels at an ambient temperature of 23±2°C.

Application environment



Telecom equipment room



Small telecom center or corridor

When the altitude increases by 220 m between 1800 m and 5000 m, the highest
operating temperature of the device decreases by 1°C.

4.2 Laser safety class

According to the laser Tx optical power, the laser safety class used by the iTN8600-I is Class
1.

When the safety class of laser used by the iTN8600-I is Class 1, the maximum Tx optical
power of the optical interface is smaller than 10 dBm (10 mW).

The laser beam inside the fiber may burn your eyes. Do not stare at the optical
interface during operation and maintenance.

4.3 Reliability specifications

Table 4-2 lists reliability specifications of the iTN8600-I.

Table 4-2

Reliability indexes

Parameter

Description

System availability

99.999%, with the annual downtime less than 5min

Average annual repair rate

< 1.5%

Содержание iTN8600-I








































































Результаты поиска

Содержание iTN8600-I

Отзывы:

Похожие инструкции для iTN8600-I

Бренды по названию

Популярные бренды

Raisecom iTN8600-I, Описание продукта

Результаты поиска

Содержание iTN8600-I

Отзывы:

Похожие инструкции для iTN8600-I

Бренды по названию

Популярные бренды