manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 60 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 60

Raisecom 
iTN2100 (P100R002) Hardware Description 

6 SDH aggregation card 

 

 

Raisecom Technology Co., Ltd. 

31 

 

Parameter 

Description 

Signal rate 

2048 Kbit/s 

Interface impedance 

75 Ω 

Electrical parameters 

Comply with ITU-T G.703 recommendations. 

 

Table 6-4

 

Parameters of the 2 MHz clock interface the OPCOM3500E-2STM1/4-M 

Parameter 

Description 

Connector 

CC3 male connector (unbalanced) 

Signal rate 

2048 kHz 

Interface impedance 

75 Ω 

Electrical parameters 

Comply with ITU-T G.703 recommendations. 

 

6.1.4 LEDs 

There are nine LEDs on the OPCOM3500E-2STM1/4-M panel, as listed in Table 6-5. 

Table 6-5

 

LEDs on the OPCOM3500E-2STM1/4-M panel 

LED 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

SWH 

Green 

Protection switchover LED 

 

Green: a switchover occurs. 

 

Off: no switchover occurs. 

ACT 

Green 

Primary/Slave LED 

 

Green: the card is a master card or there is only this 
aggregation card inserted into the chassis. 

 

Off: the card is a backup aggregation card. 

STM1 

Green 

STM-X rate LED 

 

Green: the SFP optical interface rate is STM-1. 

 

Off: the SFP optical interface rate is STM-4. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов