manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 266 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 266

Raisecom 
iTN2100 (P100R002) Hardware Description 

20 Service aggregation cards 

 

 

Raisecom Technology Co., Ltd. 

237 

 

Point-to-point networking application 

Node A multiplexes optical signals of 8 wavelength channels at the client side and transmits 
the multiplexed signals to Node B. After receiving optical signals, Node B de-multiplexes 
these signals and then sends them out. In opposite direction, Node B multiplexes optical 
signals of 8 wavelength channels at the client side and transmits the multiplexed signals to 
Node A. After receiving optical signals, Node A de-multiplexes these signals and then sends 
them out. In this mode, the iTN2100-8SU-S can be used to transmit services between Node A 
and Node B. 

Figure 20-1 shows a point-to-point networking application with the iTN2100-8SU-S. 

 

Figure 20-1

 

Point-to-point networking application with the iTN2100-8SU-S 

OADM ring network 

At the local, the iTN2100-8SU-S multiplexes optical signals of 8 wavelength channels and 
provides routing protection by establishing an Optical Add/Drop Multiplexer (OADM) ring 
network. Access points A–D can perform bidirectional add/drop multiplexing on 2-way 
optical signals. In this mode, the iTN2100-8SU-S provides a point-to-point communication 
router between any 2 access points. In addition, it facilitates upgrade and expansion. 

Figure 20-2 shows an OADM ring network with the iTN2100-8SU-S. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов