manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 187 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 187

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

158 

 

15.5.6 Alarms 

Table 15-27 lists alarms of the OPCOM3500E-120EOS×4. 

Table 15-27

 

Alarms of the OPCOM3500E-120EOS×4 

Alarm 

Cause 

Level 

Optical interface LOS 
alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

 

The local receiver fails. 

Critical 

Remote optical 
interface LOS alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

 

The local receiver fails. 

Critical 

Optical interface LOF 
alarm 

 

The sending alarm of the peer device fails. 

 

Optical signals do not match. 

 

Local receiving reference clock fails. 

Critical 

Remote interface 
LOF alarm 

 

The sending alarm of the peer device fails. 

 

Optical signals do not match. 

 

Local receiving reference clock fails. 

Critical 

Local optical 
interface E-3 alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

Major 

Local optical 
interface E-6 alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

Major 

Remote optical 
interface E-3 alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

Major 

Remote optical 
interface E-6 alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

Major 

E1 LOS alarm 

Signals are lost. 

Critical 

PDH overall alarm 

Local PDH optical interface overall alarm 

Critical 

Remote LPR alarm 

The remote device is powered off. 

Major 

Remote PDH overall 
alarm 

The PDH optical interface on the remote device has 
overall alarms. 

Critical 

 

15.5.7 Specifications 

Table 15-28 lists specifications of the OPCOM3500E-120EOS×4. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов