manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 179 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 179

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

150 

 

15.4.3 Interfaces 

Interface types 

There are three interfaces on the OPCOM3500E-P240FE panel, as listed in Table 15-18. 

Table 15-18

 

Interfaces on the OPCOM3500E-P240FE 

Interface 

Type 

Description 

ETH 

RJ45 

Service downlink interface 

A, B 

1×9 optical interface 

 

Service downlink interface 

 

TX indicates sending and RX indicates receiving. 

 

Interfaces A and B are in 1+1 protection switchover 
mode for each other. 

 

15.4.4 LEDs 

There are two LEDs on the OPCOM3500E-P240FE panel, as listed in Table 15-19. 

Table 15-19

 

LEDs on the OPCOM3500E-P240FE panel 

Interface 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

LPR 

Red 

Remote device LPR alarm LED 

 

Red: the remote device connected to the PDH interface is 
powered off. 

 

Off: no LPR occurs on the remote device connected to the 
PDH interface. 

ALM 

Red 

Alarm LED 

 

Red: LOF, 10-3, or 10-6 alarms are generated on the PDH 
optical interface, or TU-AIS and TU-LOP alarms are 
generated on the lower order path. 

 

Off: no LOF, 10-3, or 10-6 alarms are generated on the PDH 
optical interface, or no TU-AIS or TU-LOP alarm are 
generated on the lower order path. 

100M 

Green 

Ethernet electrical interface rate LED 

 

Green: the interface is working at 100 Mbit/s. 

 

Off: the interface is working at 10 Mbit/s or disconnected. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов