manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 171 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 171

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

142 

 

Interface 

Status 

Description 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

ALM 

Red 

Overall alarm LED 

 

Red: TU-AIS or TU-LOP alarms are generated on configured 
timeslots, or LOS alarms are generated on the E1 interface. 

 

Off: no alarms are generated. 

 

15.2.5 DIP switches 

The OPCOM3500E-32E1 has no DIP switches. 

The OPCOM3500E-32E1-BL has a DIP switch, as listed in Table 15-10. 

Table 15-10

 

Configurations of the DIP switch SW1 on the OPCOM3500E-32E1-BL 

SW1 

Function 

Status 

Description 

DIP bit 

Bit1 

Set the interface type 
of E1 1–16. 

ON 

Set the interface type of E1 1–16 to the 
unbalanced interface. 

OFF 

Set the interface type of E1 1–16 to the 
balanced interface. 

Bit2 

Set the interface type 
of E1 17–32. 

ON 

Set the interface type of E1 17–32 to the 
unbalanced interface. 

OFF 

Set the interface type of E1 17–32 to the 
balanced interface. 

 

 

 

By default, SW1 is all OFF. Namely, E1 1

–32 are set to the balanced interface. 

 

You can set the interface to balanced or unbalanced interface through software 

or DIP switch. 

15.2.6 Alarms 

Table 15-11 lists alarms of the OPCOM3500E-32E1/32E1-BL. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов