manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 135 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 135

Raisecom 
iTN2100 (P100R002) Hardware Description 

13 EOP cards 

 

 

Raisecom Technology Co., Ltd. 

106 

 

LED 

Status 

Description 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

ALM 

(1–8) 

Red 

Overall alarm LED 

 

Red: the LOS, LOF, AIS, or CRC_ERR alarm is 
generated on the local device. 

 

Blinking red: the LOS, LOF, AIS, or CRC_ERR alarm is 
generated on the remote device. 

 

Off: no LOS, LOF, AIS, or CRC_ERR alarm is generated 
on the local and remote devices. 

LOS 

(1–8) 

Red 

LOS alarm LED 

 

Red: local E1 LOS alarms are generated. 

 

Off: no local E1 LOS alarms are generated. 

 

13.7.5 Alarms 

Table 13-34 lists alarms generated on the OPCOM3500E-EOPS-8E1. 

Table 13-34

 

Alarms generated on the OPCOM3500E-EOPS-8E1 

Alarm 

Cause 

Level 

E1 AIS 

E1 signals are all 1 because the transmitted data is 
incorrect or the remote device outputs AIS 
signals. 

Minor 

E1 LOF 

Data sent by the upstream node is incorrect, 
because services are configured improperly or the 
hardware fails. 

Critical 

E1 CRC 

An Error on data during transmission. 

Critical 

TU-AIS 

Signals from the aggregation card fails. 

Minor 

 

13.7.6 Cables 

Table 13-35 lists cables available for the OPCOM3500E-EOPS-8E1. 

Table 13-35

 

Cables available for the OPCOM3500E-EOPS-8E1 

Card 

Recommended cable 

OPCOM3500E-EOPS-8E1 

 

CBL-E1-DB37F (40)/16NC 

 

CBL-E1-DB37F/16BNCF 

 

CBL-E1-DB37F/16BNCM 

OPCOM3500E-EOPS-8E1-BL 

CBL-E1-DB37F/8RJ45 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов