Raisecom iTN2100 Скачать руководство пользователя страница 112

Страница: 112 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

13 EOP cards

Raisecom Technology Co., Ltd.

13.1.3 Interfaces

Interface types

There are 2 interfaces on the OPCOM3500E-EOPFE panel, as listed in Table 13-1.

Table 13-1

Interfaces on the OPCOM3500E-EOPFE panel

Interface

Type

Description

–

MiniUSB

Debugging interface

RJ45

Used for transmitting 1-way 100 Mbit/s Ethernet services.

Interface parameters

Table 13-2

lists parameters of interfaces 1–2 on the OPCOM3500E-EOPFE.

Table 13-2

Parameters of interfaces 1–2 on the OPCOM3500E-EOPFE

Parameter

Description

Connector type

RJ45

Interface speed

10/100 M bit/s/ auto-negotiation

Maximum supported frame length

1916 Bytes

Line order

Auto MDI/MDI-X

Duplex mode

Full duplex/half duplex/auto-negotiation

Flow control



Full duplex: IEEE 802.3x-based flow control



Half duplex: back-pressure flow control

13.1.4 LEDs

There are 4 LEDs on the OPCOM3500E-EOPFE panel, as listed in Table 13-3.

Table 13-3

LEDs on the OPCOM3500E-EOPFE panel

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

Содержание iTN2100

























































































































































































































































































































Результаты поиска

Содержание iTN2100

Отзывы:

Raisecom iTN2100, Описание аппаратуры, Страница: 112 / 312

Результаты поиска

Содержание iTN2100

Отзывы: