manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры, Страница: 108 / 312

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 108

Raisecom 
iTN2100 (P100R002) Hardware Description 

12 TDMoP card 

 

 

Raisecom Technology Co., Ltd. 

79 

 

12.1.3 Interfaces 

Interface types 

There are 17 interfaces on the iTN2100-CES-16E1T1-BL panel, as listed in Table 12-1. 

Table 12-1

 

Interfaces on the iTN2100-CES-16E1T1-BL panel 

Interface 

Type 

Description 

– 

MiniUSB  Debugging interface 

1–16 

RJ45 

E1 balanced interface. Each RJ45 interface provides 2-way E1 
services. 

 

Interface parameters 

Table 12-2 lists parameters of interfaces 1–16 on the iTN2100-CES-16E1T1-BL. 

Table 12-2

 

Parameters of interfaces 1–16 on the iTN2100-CES-16E1T1-BL 

Parameter 

Description 

Connector type 

RJ45 

Interface impedance 

120Ω balanced interface 

Interface speed 

2.048 Mbit/s 

Coding type 

HDB3 

Supported frame format 

Unframed, PCM31, PCM31C, PCM30, and PCM30C 

Frame structure 

Comply with ITU-TG.703/ITU-TG.704 recommendations. 

Clock 

Comply with ITU-TG.823 recommendations. 

Jitter 

Comply with ITU-TG.823 recommendations. 

Electrical feature 

Comply with ITU-TG.703 recommendations and support 
short distance. 

Wander feature 

Comply with ITU-TG.823 recommendations. 

 

12.1.4 LEDs 

There are 18 LEDs on the iTN2100-CES-16E1T1-BL panel, as listed in Table 12-3. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов