Raisecom iTN2100 Скачать руководство пользователя страница 105

Страница: 105 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

11 Clock card

Raisecom Technology Co., Ltd.

Table 11-5

LEDs on the iTN2100-TSU panel

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

LOCK

Red

Lockout state LED



Red: the current 1588 V2 time is in unlock state.



Off: the current 1588 V2 time is in lockout state.

ALM

Red

Fault alarm LED



Red: LOS alarms are generated on current 2-way external
clock signals. The ALM LED is off when at least one-way
signal is displayed as normal/lof.



Off: currently, at least one-way external clock signal is input
properly.

11.1.5 Specifications

Table 11-6 lists specifications of the iTN2100-TSU.

Table 11-6

Specifications of the iTN2100-TSU

Parameter

Value

Dimensions

25 mm (width) × 232 mm (depth) × 240 mm (height)

Weight

0.4 kg

Max. power consumption 20 W

Содержание iTN2100

























































































































































































































































































































Результаты поиска

Содержание iTN2100

Отзывы:

Raisecom iTN2100, Описание аппаратуры, Страница: 105 / 312

Результаты поиска

Содержание iTN2100

Отзывы: