Rain Bird ESP-10ME3 Скачать руководство пользователя страница 4

ESP-ME3 Controller

4

EN

Installation

Mount Controller

 

B

NOTE: Choose a suitable mounting location close 

to a 120VAC wall outlet.

Drive a mounting screw into the wall, leaving an 
1/8 inch gap between the screw head and the 
wall surface (use the supplied wall anchors if 
necessary), as shown.

Locate the keyhole slot on back of the controller 
unit and hang it securely on the mounting screw.

1/8 IN.

a

b

Open the front panel, and drive three additional 
screws through the open holes inside the 
controller and into the wall, as shown.

c

a

b

MASTER 
VALVE

COM

COM

MV

MV

11

22

SENS

SENS

e

c

Connect Valves

Route all field wires through the opening at the 
bottom or back of the unit. Attach conduit if 
desired, as shown.

 

C

WARNING

Do not route valve wires through the same opening 
as power wires.

Connect one wire from each valve to the terminal 
on the 

Base Module

 or 

Station Module

 that 

corresponds to the desired station number (1-22).

Connect a field common wire to the 

COM

 

(common)terminal on the 

Base Module

. Then 

connect the remaining wire from each valve to 
the field common wire, as shown.

To perform a Valve Test, connect the common wire 
to the 

COM

 terminal and the power wire to the 

VT 

terminal. This will immediately turn the valve ON.

Connect Master Valve (optional)

Connect a wire from the master valve to the 

MV

 

(master valve) terminal on the 

Base Module

Then connect the remaining wire from the master 
valve to the field common wire, as shown.

Содержание ESP-10ME3




















Отзывы: