manualshive.com logo in svg

Rail King GG-1 ELECTRIC ENGINE, Руководство оператора

Поделиться
Скачать
Rail King GG-1 ELECTRIC ENGINE Скачать руководство пользователя страница 21

FYS/PSA

Remedy

Once in FYS/PSA, the engine 
doesn’t go into reverse.

When the FYS/PSA enters its last 
sequence the bell automatically 
comes on.

When FYS/PSA is enabled, 
pressing the whistle and bell 
buttons has no effect.

I push the direction button but the 
next sound clip in the sequence 
does not play or the engine does 
not come out of FYS/PSA after 
fourth press of the direction 
button.

So that FYS/PSA effects can be 
as realistic as possible, Proto-
Sound 2.0 disables the reversing 
unit whenever FYS/PSA is 
enabled.  This way the engine 
remains still at its stop as the 
operator cycles through the 
FYS/PSA sequences.

FYS is programmed to start 
ringing the bell at that point.  After 
approximately 12 seconds it will 
automatically turn off.

Because FYS must control various 
effects in each sequence, Proto-
Sound 2.0 takes control of these 
sound effects until you exit 
FYS/PSA.

Each FYS/PSA clip must play for 
approx. 30 seconds before 
FYS/PSA will advance to the next 
step in the FYS/PSA cycle.  Wait 
at least 30 seconds in each 
FYS/PSA sound clip before 
pressing the direction button.

 GG-1 Electric Engine

21

Содержание GG-1 ELECTRIC ENGINE



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды