Rail-Ability Komatsu D41 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 34

Rail-Ability Komatsu D41 Series Скачать руководство пользователя страница 8

Issue 1

Page 8 of 34

Initial Issue 19 December 2017

Engineering Manager



See the network rail VAB engineering acceptance certificate for additional, specific machine
limitations of use.



This manual should be used in conjunction with the operators Safe System of Work and OEM
manuals.



Modifications to the vehicle must be authorised by rail-ability and a plant acceptance body that
will issue an amended engineering conformance certificate. Failure to get approval will
invalidate the existing engineering conformance certificate.



This manual should remain with the machine at all times. All OPERATING personnel should be
aware of its location and contents.



It is important that all personnel are fully trained and familiar with the machine and that they
have read and understood the information contained within this manual before operating in the
site conditions for which the machine was designed.



Only authorised staff may start, operate or interface with the vehicle.



The user of the vehicle shall only operate the machine IN ACCORDANCE TO THIS MANUAL
and avoid overloading.



All personnel are obliged to take precautions given by the railway infrastructure manager.



Personnel are NOT permitted between moving vehicles.



The  vehicle  may  only  operate  with  the  access  adjacent  to  access  or  a  line  closed  to  all  train
movements  or  the  documented  safe  system  of  work  must  take  account  of  adequate  safe
clearances to adjacent lines.



The vehicle is not suitable for operation of spring loaded points.



The vehicle is not for use on live third/forth rail areas.



The vehicle is not designed to tow or propel other machines.



The machine is not designed to tow or propel rail trailers.



The machine is not designed to carry or lift loads.



The machine does not have a working mode on track. It has a travel mode only.



The machine brakes should be checked prior to each use.



Each machine function and interlock should be tested before the machine is put on track and /
or used for work.



For working in dusty environments the machine should be equipped with the optional
pressurised cab system.



Shearing,  entrapment:  the  machine  has  a  lot  of  moving  parts  that  are  impossible  to  protect,
therefore  the  operator  shall  always  be  aware  of  this  residual  risk  and  keep  clear  from  the
moving  parts  in,  particularly  from  the  blade  assembly  and  tracks.  The  operator  is  held
responsible  not  only  for  them  self  but  also  for  those  working  in  proximity  of  the  machine
including any that are not authorized.

«
...
6
7
8
9
10
...
»

Содержание Komatsu D41 Series



































Отзывы:

Нет отзывов