Raidon
iR8023 Quick Setup Guide
Package Contents and Product Views
Front View
Rear View
1.
LCD Display
2.
UP/DOWN Button
3.
ESC Button
4.
Enter Button
5.MUTE Button
6.
Power Failure Indicator
7.
HDD Tray Handle
8.
HDD Tray Ejection
9.HDD tray key lock
10.HDD Access Indicator
Open the package and you should find the following:
Please check the product and accessories for any defect or missing parts. If you
have any questions, please contact your product supplier.
Please visit the official website - Download page (https://www.raidon.com.tw)
to download drivers and other related resources.
˙
˙
SAT
A
SAT
A
SATA Cable
SATA Power Cable
Internal host shell schematic
1
2
iR8023
iR8023
Computers or servers must be with SATA I, SATA II, or SATA III interface.
Only support 2242/2260/2280 M.2 SATA SSD dimension.
The independent drive at the top cannot be set into RAID mode with primary or
secondary drive. It is an independent drive.
You are strongly advised to set the storage mode before using your iR8023. (The default
setting is the RAID 1.)
Once the drive mode configuration has been completed, re-configuration using the
same hard drives to set the drive mode will result in complete data loss. If you must
change the drive mode, make sure to backup all data prior to the mode change.
A reboot is required after adding or changing RAID mode to ensure that the update is
completed to the new RAID mode.
iR8023 product allows user to simultaneously use the two different hard drives from two
different manufactures. However, if the user expects a better efficiency, we strongly
recommend the user to use the two hard drives from the same manufacturer.
Please make sure that the two hard drives are free from bad blocks or defects prior to
installation in order to avoid system crashes or data loss.
The actual storage capacity of iR8023 recognized by the system may differ from the
total capacity stated on the hard drives combined once the drives have been formatted.
It is highly recommended for user to back up important data contained within the iR8023
unit on a regular basis or whenever the user feels necessary to a remote or a separate
storage device. RAIDON will not be responsible for any lost of data caused during the
use of the unit or the recovery of the data lost.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Hardware Installation
Please install iR���� as the following instruction.
��. Power on your system after hardware installation is completed, and your
operating system will automatically detect the hard drives from booting.
Then follow the steps from your operating system to partition and format
the drives when necessary, device will be ready to use once the format is
completed.
10
1.
Cooling Fan
2.
3-pin Fan Connector
3.
RS232 Connector
4.
7-pin SATA Connector (Standalone HDD)
5.15-pin Power Connector
6.7-pin SATA Connector (RAID HDD)
Standalone HDD
Pri HDD
Ｓ
ec HDD
iR8023 Device
x1
Quick Installation
Guide
x�
Screws & Pins
Contents of Product Package
Internal SATA Cable
x1
RS232 Port: For industrial control system or IPC to monitor the hardware status.
More information, please contact your sales window or [email protected]
LED Instruction
Hard Disk Status on LCD Screen
Description of Front Panel Operation
Select Items
Back to next level or Cancel
Enter to next level or Confirm
Important Notice
RAIDON RAIDbox2
RAID-1 vxxxxxx.x
Pri HDD : OK
Sec HDD : READY
�. Booting and Normal status
�.Fan Failure
Pri HDD : OK
Sec HDD : READY T
�. HDD Failure
Pe i HDD:OK
Sec HDD:FAILED
Pei HDD:FAILED
Sec HDD:OK
�. Over Temperature (≥��°C)
Pri HDD : OK F
Sec HDD : READY
When “T” is shown, it's an alert of system over heating, but it would still work fine.
And as long as the ambient temperature is improved, system shuts off the alert.
�. Rebuilding
Rebuilding
Sec→Pri 32%
RAIDON
is one brand under
RAIDON TECHNOLOGY, INC.
Thank you for choosing
RAIDON’s
product.
The information provided in this manual was checked before publication, but the actual product
specifications may have changed before shipping; Latest product specifications and updates can be
found at
www.RAIDON.com
.tw or through your sales representative. No separate notifications will be
provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product information,
instruction manuals, or firmware, please contact S
for assistance.
All product-related content in this manual are copyrighted by
RAIDON TECHNOLOGY, INC.
Status
Standalone HDD
RAID HDD
System Indication
Buzzer
No HDD
N/A
Red light always on Purple light always on
ON
HDD Idle
Blue light always on
Blue light always on
Blue light always on
N/A
Access
Blue light always on
N/A
Rebuilding-Source
Blue light always on
Blue light always on
Blue light always on
N/A
Rebuilding-Target
Blue light always on
Blue light always on
N/A
Fan Failure
Blue light always on
Blue light always on Purple light always on
ON
V1.0 (Nov. 2021)
1. Unlock the M.2 SATA Bridge Tray Key Lock
and
push the HDD tray ejection to the right
.
2. Pull out the M.2 SATA Bridge Tray.
3. Remove the screws of the upper cover of the
M.2 SATA Bridge.
4. Open the upper cover .
5. Insert M.2 and fix the screw.
6. Remove the paper from the heat sink in the
upper cover and put the upper cover back.
7. Fix the screws.
8. Install the M.2 SATA Bridge tray
back into the iR8023.
.
�. Install device into one of the
CD-ROM bays with screws from
the accessory kit.
Then properly connect SATA cable
and SATA power cable from your
system to device.
1
2
3
4
5
6
7
8
Lock
Unlock
