20
www.raider.bg
The dust bag stays in place when you release
the clamp.
8. OPERATION
Using the mitre saw Fig. 1
Before use, always check for faults or defects!
• Set the desired sawing angle of the machine.
• Put the plug into the socket.
• Fix the piece of work in place using the
clamps (7): make sure that the material is well
clamped in place!
• Hold the material tightly on the left side while
making sure that you keep a safe distance from
the blade of the saw.
• Turn on the machine using the switch (1).
• Make sure that the saw blade has reached
full speed before allowing it to touch the piece of
work to be sawn.
• Use knob (3) to raise the protective cover
lock.
• Now bring the saw slowly downwards so that
the saw blade saws through the piece of work
and passes through the slot in the table. Do not
put any pressure on the saw. Give the machine
time to saw through the piece of work.
• Bring the machine gently up again and
switch it off by letting go of the switch (1).
Using the slide-function Fig. 1
The machine must be firmly bolted to a
workbench.
Use the slide-function for sawing wide
workpieces:
• Fix the piece of work in place using the clamp
• Screw up the knob (10) a half turn
anticlockwise.
• Slide the machine completely towards
yourself
• Turn on the machine using the switch
• Bring the saw slowly downwards so the saw
blade saws through the piece of work
• Push the machine slowly backwards (in
direction of guide fence)
• Bring the machine gently up again and
switch it off by letting go of the switch
Using the laser Fig. 2
• To switch on the laser , press the on/off
switch 2.
• To switch off the laser , release the on/off
switch 2.
9. SERVICE AND MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you carry
out any maintenance of the mechanism.
Slide rails
Dirt can damage the slide rails and thereupon
the operating of the machine.
• Clean the slide rails regularly with a soft
cloth.
• Drip some lubricating oil on the slide rails
• Move the mitre saw forwards and backwards
so the oil spreads over the complete rails
These machines are designed to function for a
long time without any problems with a minimum of
maintenance. By cleaning the machine regularly
and using it in the correct way you can contribute
to a long life of your machine.
Cleaning
Clean the machine housing regularly with
a soft cloth, preferably after each time you use
the machine. Make sure that the ventilation slots
are free of dust and dirt. For stubborn dirt use a
soft cloth dampened with soapy water. Never use
solvents such as benzene, alcohol, ammonia,
etc.
These types of solvents can damage the
plastic parts.
10. Problem solving
10.1. The motor does not start
• The plug is not in the socket
• The power cord is broken
• The switch is defective. Take the machine to
your dealer for repair.
10.2. The saw cut is not even (jagged)
• The saw blade must be sharpened
• The saw blade is mounted back to front
• The saw blade is clogged with resin or
sawdust
• The saw blade is not suitable for the piece of
work being used
10.3. The height and/or mitre lever is
obstructed
• Chips and/or dust must be removed
10.4. The motor has difficulty in reaching full
speed
• The extension cord is too thin and/or too long
• The mains voltage is less than 230 V
10.5. The machine vibrates excessively
• The saw blade is damaged
10.6. The machine becomes excessively hot
• The ventilation slots are blocked. Clean them
out with a dry cloth.
10.7. The electromotor runs unevenly
• The carbon brushes are worn out. Replace
the carbon brushes or consult your dealer.
Содержание RDP-MS11
