11
Before operation, read the operating instruction and follow the safety instructions.
Important!
When using
equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the
c o m p l e t e
operating manual with due care. Keep this manual in a safe place, so that the information is available at
all times. If
you give the equipment to any other person, give them these operating instructions as well. We accept no
liability for
damage or accidents which arise due to non-observance of these instructions and the safety information.
1. SAFETY INFORMATION
• Do not allow children or people unfamiliar with the instructions to use the tiller. Persons under 16 should not use it .
• The power cord must be unplugged before the inspection , repair or service activities.
• handling the cutter liable to third parties for damages caused during the operation of this machine .
• Work only in daylight or ensure adequate artificial lighting.
• Always check the appliance for damage.
• Check to make sure that all safety devices are installed and functioning properly.
• Never use the machine if you are tired .
• Never use the appliance in a confined or poorly ventilated areas or in close proximity to flammable or explosive liquids, gases
or vapors.
• Stop the engine and disconnect the plug from the mains before removing the blocking or blocked items before checking,
cleaning or service in the event that you encounter a foreign body .
• Before use, you should check that are not worn or damaged cutting tools , fastening bolts and all the cutting device.
• Damaged parts of the unit must be replaced by a specialist. We only use original spare parts.
• When installing or removing the blade to follow instructions and to use protective gloves .
• Check the area on which the router will be used and remove all objects which can be placed in it and cause blockage . Before
milling to remove foreign bodies . Notice of extension cords that will be needed at work.
• When using a router , you must be a sturdy shoes and long pants . Never work barefoot or in sandals.
• When starting the engine cutter should not be raised.
• Never place hands or feet under rotating parts .
• There must be a safe distance determined by the length of the handle.
• If you are working on sloping ground should be milled across the slope .
• Do not use cutter on terrain with slopes over 15%.
• Before you lift the cutter to transport it , you need to cut power to release the connection cable and wait for stopping knife.
• Be careful at work near the router no people, especially small children or animals. Take care of the small distance to work
safely is 10 m
• Store the cutter in a dry place inaccessible to children.
• Electrical parts of the router should be repaired by a specialist .
• Only use extension cables must have a cross -section of at least 1.5 mm2 . Plug connections have to wear contacts, and the
joints are reserved by the water spray. Extension wire must go through the handle and reach combination switch plug . Before using
the wire check it for damage.
Never operate if wires are not perfect . If during work breaks conductor , immediately unplug the unit and then check what the
defect.
• When starting the engine cutter must not be tilted and turned .
• If the router begins to vibrate abnormally strong now have to be carried out.
• Make sure all nuts, bolts and screws are always properly tightened and the appliance is in good working condition.
• If you encounter a foreign body , immediately turn off the engine and check the router for damage and make necessary repairs
before you start it again.
• cutter must not let it rain . The soil should not be wet or very damp .
• During operation, always watch out for the security position of the instrument .
• Use the device only in stepping pace.
• Be especially careful when you change direction when working on slopes .
• Be especially careful when you turn the router in another direction or shall draw to yourself.
• Switch off the engine and remove the cable when router is transferred from one to another work site or transported to another
location.
• Start the device with care and according to the manufacturer’s instructions . Watch for a sufficient distance between the legs
and cutting tools .
• Do not lift and carry the router with the engine running .
• Turn off the engine when moving away from the router .
• Allow the engine to cool before storing in a confined space cutter .
• Regularly check the bag for collecting grass for signs of wear and the ability to act.
• Before adjusting , cleaning and damage to unplug the power cord from the mains.
• connecting contacts must be made of rubber or soft PVC or other thermoplastic material , or be coated with such material .
• Make sure the power cord is not wrapped around obstacles hindering free movement .
• Do not connect or disconnect the motor frequently within a short period of time.
• Consequently, the ripple of the voltage of the motor speed can be changed. In case of insufficient supply powerful network
some users within the same power circuit can be affected when using electric mower . You can try to prevent this by switching to
another circuit with less powerful consumers .
• Unplug the power cord from the network :
- When you put the power mower - the occurrence of unusual vibrations Warning ! Read all safety information and instructions
. Failure to follow the safety precautions and instructions may result in electric shock, fire and / or serious injury. Keep all safety
instructions and the instructions in the future.
2. LAYOUT (Fig. 1-3)
1. Top push bar
2. Bottom push bar
3. Motor unit
4. Hoe blades
5. Cable strain-relief clamp
