Raider RD-AB01, Руководство пользователя

Страница: 14 / 58

14 www.raider.bg
We at Euromaster Import-Export LTD. are
extremely proud of our people and our products.
Our continued growth and success is based
upon stressing quality and craftsmanship in the
manufacture of our products. At Euromaster
Import-Export LTD. there is a sense of pride and
dedication to you that extends throughout our
entireorganization.
Each airbrush is carefully machined, inspected,
and assembled by hand, then tested in actual
use to be sure it matches high standards of
quality.
This dedication to excellence enables us to stand
behind all of our products and offer the following
warranty on all of our airbrushes.
WARRANTY
Your airbrush is warranted against all
manufacturing defects of materials and
workmanship for a period of two years from the
date of purchase. Any part or material that is
defective or worn so as not to be useable within
this period will be repaired or replaced at our
expense. This warranty does not cover damage
caused by negligence, accident or units which
have been abused or altered in any way.
INTRODUCTION
This model bottom feed is among the most
versatile of airbrushes. It permits great flexibility
inregulation of color and air without work
stoppage.
Different size spray regulators, tips and needles
are quickly interchangeable to allow greater
diversity in materials and coverage. It is used
by Fine Artists, TShirt Artists, Illustrators, Fabric
Designers, Custom Automotive Painters and
Professional Model Makers.
It can spray properly reduced artist acrylics,
acrylic enamel and lacquers, gouache, fabric
colors, inks and dyes, ceramic colors and glazes,
water colors and of course.
SPRAY CHARACTERISTICS OF HEAD
ASSEMBLIES
OF INTERNAL MIX AIRBRUSHES:
• F has the smallest opening for extra fine
detailing. It is designed for use with materials of
a low viscosity – very thin acrylics, water colors,
inks and dyes.
• M has a medium opening for fine detailing.
It will spray approximately twice the amount
of materials as the F. This head will handle
such viscosities as fabric paints, thinned down
acrylics, gouaches, hobby lacquers,
enamels, etc.
• L has the largest opening and will spray
approximately four times the amount of fluid
as the F. The L is designed to be used with
materials of higher viscosity – automotive paint,
ceramic glazes, acrylics, etc.
READ INSTRUCTIONS CAREFULLY BEFORE
OPERATING
TO OPERATE
1) Attach hose to air supply (CO2 tank,
compressor or aerosol propellant can) then
holding air hose in hand, attach airbrush to air
hose by gently turning in clockwise motion on to
fitting.
Tighten air hose snugly into place.
2) When air is regulated, pressure should be
between 15 to 50 p.s.i. Normal operating
pressure is 30 p.s.i. We recommend a pressure
gauge (No. 50-054) and/or water trap
(No. 50-051) in conjunction with compressor
where humidity is a problem. A compressor
or CO2 tank is more practical for larger jobs
and prolonged spraying.
3) To attach jar or color cup, insert stem from jar
into hold located in bottom of airbrush near
head. Insert the stem into the airbrush and give
a 1/4 counter clockwise.
This will snug your jar (bottle) or color
cup assembly in place. To remove, pull down
and rotate jar (or cup) assembly counter
clockwise again.
4) When the trigger of the airbrush is depressed
air is released. As the rigger is drawn back
(while still depressed) fluid is released. The
further the trigger is pulled back, the larger
the volume of pain if sprayed. A fine line or
small dot is achieved by working very close to
the work surface with the trigger drawn back
slightly. A broad pattern is achieved by moving
the airbrush away from the work surface and
pulling the trigger all the way back. The proper
triggering of the airbrush is down for air
movement, back for paint flow, and forward to
stop paint flow and up to stop the air.
LEARN TO TRIGGER