manualshive.com logo in svg

Radyne QAM256, Инструкция по установке и эксплуатации

Поделиться
Скачать
Radyne QAM256 Скачать руководство пользователя страница 24

User Interfaces 

 

QAM256 Digital Video Modulator and Upconverter 

4-8 

 

TM077 - Rev. 4.0 

4.5  Connecting the Terminal 

 
1. 

Connect the computer to the QAM256 Remote Connector (J5) on the rear of the unit 
using the RS-232 Cable. 

 
2. 

Enable the terminal by selecting Terminal Mode (located under the System - Control 
Mode Menu) from the front panel. 

 
3. 

Verify that your emulation software is set to the following: 

 

8 data bits 
no parity 
1 stop bit 

 

Modify the QAM256 selection, if necessary, to match the settings (the Front Panel 
‘SYSTEM’ Sub-Menu contains all the Terminal Emulation Controls). 

 

4.6  Terminal Screens 

 
1. 

Modem configuration can be monitored and controlled via a full screen presentation of 
current settings and status.  The <Esc> Key redraws the entire screen and aborts input 
any time.  The Spacebar refreshes the status area and is used to scroll through selection 
when in user input mode. 

 
2. 

To modify an item, the user simply presses its terminal selection followed by <Enter>.  
The modem responds by presenting the options available and requesting input.  If the 
input is multiple choices, the user is prompted to use the Spacebar to scroll to the desired 
selection and then press <Enter>.  An input can be aborted at any time by pressing 
<Esc>.  Invalid input keys cause an error message to be displayed on the terminal.  
Some input or display status only appears when the user has the right access levels. 

 

Содержание QAM256
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды