Radleys Reactor-Ready Скачать руководство пользователя страница 14

Страница: 14 / 20

8.8 Assembling the thermofluid hoses

8.8.1

Attach one of the Quick Release Insulated

Hoses to the lower Inlet Draindown Manifold by

screwing the stainless female coned swivel fitting

on the hose onto the stainless steel horizontal

screw thread fitting on the Manifold. Tighten fully

using a wrench to ensure no leakage.

8.8.2

Attach the second Quick Release Insulated Hose to the upper Outlet Manifold as in 8.8.1.

8.8.3

Attach the lower PEEK hose to the vessel lower side arm with the aid of the quick

coupling connector. Visually check that the two Viton o-rings are properly located in the

grooves of the coupling before pushing the coupling onto the glass side arm. A slight twisting

motion while pushing the fitting on may aid this process. Once the coupling is fully engaged

on the side arm, screw the red (Rodaviss) screw

cap (located on the side arm) on to the hose

connector, and hand tighten.

8.8.4

Attach the upper hose to the vessel upper

side arm with the aid of the quick coupling

connector as in 8.8.3.

8.8.5

Only fine adjustments of the height of the

manifolds can be made after the hoses are

attached to the vessel.

8.9 Assembling the Overhead Stirrer

8.9.1

Slide the spindle of the Stirrer Drive

Coupling into the chuck of your overhead stirrer. Fully tighten the chuck.

8.9.2

Loosen the locking knobs and slide the Stirrer Support I-Brace up to give sufficient

clearance between the Brace and the reaction vessel. re-tighten the locking knobs.

8.9.3

Identify the size of the support rod on your overhead stirrer. There are two common

sizes, 13mm diameter or 16mm diameter. With the use of a removable adapter the sliding

boss is able to accommodate different sizes of overhead stirrer rods. With the adapter in

place stirrer rods of up to 13.5mm diameter can be accommodated. Removal of the adapter

(by gently prising from the hole with a suitable implement) allows stirrer rods of up to 16.5mm

to be used.

8.9.4

Locate the rod of the stirrer motor into the hole in the sliding boss. Position the sliding boss

and stirrer motor so that the Stirrer Drive Coupling is in line with the metal cap on the Stirrer

Guide below, then tighten the locking knobs on the top and front of the sliding support boss.

8.9.5

The Stirrer Support I-Brace and sliding support boss are designed to allow the stirrer

motor to be moved forwards and backwards, left or right and up or down.

8. Set-Up & Operation

- Continued

Page 13

8.8.1

8.8.3

Reactor-Ready - Lab Reactor

Important Note -

To aid the

sliding movement of the stirrer

support boss along the Stirrer

Support I-Brace, it is advisable to

manually support the weight of

the stirrer whilst sliding sideways.

Important, Important,

8.9.1

8.9.4

8.9.5

8.8.5

Содержание Reactor-Ready





















Результаты поиска

Содержание Reactor-Ready

Отзывы:

Бренды по названию

Популярные бренды

Radleys Reactor-Ready, Инструкция по эксплуатации

Результаты поиска

Содержание Reactor-Ready

Отзывы:

Бренды по названию

Популярные бренды