Radius Belalatus ten Скачать руководство пользователя страница 3

 

O p e r a t i n g   i n s t r u c t i o n s   -   B e l a l a t u s  

ten

_ v 0 1 . d o c x

   

 

S e i t e  

3

  v o n  

9

 

 

 

Operating instructions Radius belalatus® ten fan-

shaped awning 

for end users

 

 

1.3

 

Using the belalatus® ten 

When installing and operating the fan awning, the intended use must be observed: 

  The fan-shaped awning (fan) is to be used exclusively as weather-resistant sun 

protection. The wind resistance of the open fan is limited and the information on this 
assumes that it is installed according to the instructions. 

  The wind resistance of the opened fan is limited. The fan must be closed when the wind 

picks up or gusts of wind are approaching. Unattended fan awnings must not remain 
open. Surprising strong winds could cause serious damage. 

  Before opening and closing the fan, check that there are no obstacles in the travel range. 

  The fan awning may not be modified or hung with foreign material. 

  Only use the sunblind in an undamaged condition and pay attention to possible faults. 

Arrange for its professional repair before further use! 

  Only use original Radius accessories and spare parts to ensure safety, unadulterated 

comfort and flawless function. 

  Where appropriate, a self-standing, stable climbing aid shall be used to attach or remove 

a protective cover. Make sure that it cannot tip over or slip away. 

  The individual fan motors have overload protection. If a motor is moved for 6 minutes, it 

is blocked for 18 minutes. Only after this time is further operation possible again. 
However, an exception is a "priority signal" from a connected wind monitor or KNX 
system. 

  Conversions or changes to the fan, control unit, remote control, motor and all connecting 

cables are prohibited! 

  The controller may only be operated with the mains voltage specified on the type plate! 

  It is essential to use the supplied power cord. Operating the control unit with a damaged 

power cable is prohibited! 

  Electrical cables must not be exposed to any danger of crushing, bending or tensile 

stress. 

  It shall be possible to switch the control system on and off by means of an electric switch 

which can be operated quickly and easily even in an emergency situation. 

 

If the control unit is exposed to sunlight, it must be protected from direct sunlight 
with a well ventilated protective hood. The control unit has an IP 65 water 
protection rating

.

 

 

 

 

 

 

 

 

 

Содержание Belalatus ten










Отзывы: