Radio Shack XL-50 Скачать руководство пользователя страница 15

15

Care

ˆ

Care

To enjoy your amplifier for a long time:

• Keep the amplifier dry. If it gets wet,

wipe it dry immediately.

• Use and store the amplifier only in nor-

mal temperature environments.

• Handle the amplifier gently and care-

fully. Do not drop it.

• Keep the amplifier away from dust and

dirt.

• Wipe the amplifier with a damp cloth

occasionally to keep it looking new.

Modifying or tampering with the amplifier’s
internal components can cause a malfunc-
tion and might invalidate its warranty and
void your FCC authorization to operate it. If
your amplifier is not performing as it should,
take it to your local RadioShack store for as-
sistance.

REPLACING A FUSE

If the amplifier does not operate, you might
need to replace the red power cable’s 7.5-
amp SFE-type fuse or the 7.5-amp blade-
type fuse on the amplifier’s back panel.
Check both fuses.

Important: Let the amplifier cool down and
see if it starts again before you assume a
fuse needs to be replaced.

Caution: Do not use a fuse with ratings other
than those specified. Doing so might damage
your amplifier.

Replacing the SFE-Type Fuse

1. Disconnect the cable from the vehicle’s

negative (–) battery terminal.

2. Push together and twist the fuse

holder’s parts on the red power cable
until they spring apart. Then remove the
fuse.

3. If the fuse is blown, replace it. Use only

an SFE-type fuse with the proper rating.
The fuse must be 7.5 amps.

4. Reassemble the fuse holder by inserting

the fuse into the longer of the fuse
holder’s ends, and pushing together and
twisting the two parts until they latch
together.

5. Reconnect the cable to the vehicle’s

negative (–) battery terminal.

Replacing the Blade-Type Fuse

1. Disconnect the cable from the vehicles

negative (–) battery terminal.

2. Grasp the fuse’s plastic end and pull it

out.

3. If the fuse is blown, replace it. Use only

a blade-type fuse with the proper rating.
The fuse must be 7.5 amps.

4. Grasp the new fuse’s plastic end and

push it in.

5. Reconnect the cable to the vehicle’s

negative (–) battery terminal.

Fuse

12-2013.fm  Page 15  Tuesday, May 9, 2000  9:09 AM

Содержание XL-50

















Отзывы: